Airtac MIJ Adjustable Cylinder MIJ10X60-30
The AirTAC Airtac MIJ Adjustable Cylinder MIJ10X60-30 is a genuine double acting, adjustable stroke round-body mini air cylinder with a Ø10mm bore and 60mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface makes it a compact drop-in for standard mini-cylinder fixtures.
- BoreØ10 mm
- Stroke60 mm
- Port sizeM5×0.8
- Acting typeDouble acting, adjustable stroke
- Rod threadM4×0.7
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ10X60-30
Dial in your forward end position on the fly with the AirTAC MIJ10X60-30, a round-body stainless steel mini cylinder built for ISO 6432 mounting interfaces. A external stop screw lets you shorten the extend stroke by up to 30 mm directly on the machine, covering multiple stop distances with a single part number while the retract stroke remains full. The Ø10 mm bore delivers 39.3 N of push force at 0.5 MPa, yielding a safe working load of about 24 N or roughly 2 kg of vertical lift with a 2:1 margin.
The riveted stainless barrel and piston rod resist mild corrosion and routine washdowns, making it suitable for compact assemblies where space is tight. Air connects via an M5x0.8 port, and fixed TPU bumper pads decelerate the piston at the stroke ends. Because this specific SKU lacks the -S magnet option, it cannot host CMSG, DMSG, or EMSG sensors for position detection.
Airtac MIJ Adjustable Cylinder MIJ10X60-30 Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ10X60-30 |
|---|---|
| Series | MIJ ISO 6432 mini cylinder |
| Bore size | Ø10 mm |
| Stroke | 60 mm |
| Acting type | Double acting, adjustable stroke |
| Port size | M5×0.8 |
| Rod thread | M4×0.7 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø10mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 39 N | 33 N |
| 0.7 MPa | 55 N | 46 N |
| Max (@1.0 MPa) | 8 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MIJ Adjustable Cylinder MIJ10X60-30
| MIJ | ISO 6432 round-body mini cylinder (adjustable-stroke). |
|---|---|
| 10 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| -30 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ10X60-30 Is Used
Adjustable Stop Feeding
Trim the extend stroke by up to 30 mm to push varied lengths of small stock into a machining fixture without swapping cylinders.
Light Parts Ejection
Utilize the 39.3 N push force to reliably kick lightweight plastic or aluminum components out of a conveyor chute at a precise endpoint.
Tolerance Take-Up Sorting
Fine-tune the forward position on-site to compensate for minor mechanical wear in a small-parts diverter gate handling 2 kg loads.
Is the Airtac MIJ Adjustable Cylinder MIJ10X60-30 the Right Cylinder?
When sizing this actuator, verify your force needs against the 39.3 N push and 33 N pull figures at 0.5 MPa. If your application requires less force, the smaller Ø8 bore provides 25.1 N of push; stepping up to the Ø16 bore increases that to 100.5 N. The 30 mm adjustment window is ideal for taking up mechanical tolerances or fine-tuning a feed length without machining new stops. Remember that the stop screw only sets the forward end position—it is not a mid-stroke lock. The piston will drift if air pressure drops, so install an external pilot check valve if you need to hold a load vertically. Mounting options include LB foot, FA flange, and TC trunnion brackets, but the SDB pivot block is not available for this adjustable variant.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ10X60-30 FAQ
This double-acting cylinder uses an M5x0.8 air port and generates 39.3 N push / 33 N pull at 0.5 MPa, and 55 N push / 46.1 N pull at 0.7 MPa. The theoretical maximum force is 8 kgf at 1.0 MPa. It operates at speeds between 30-800 mm/s.
An external stop screw shortens the extend stroke by up to 30 mm on-site (usable extend 30-60 mm), while the retract stroke remains full. This SKU does not include a magnet (-S), so it cannot accept CMSG, DMSG, or EMSG sensors. The stainless build and fixed TPU bumpers handle mild washdowns and end-of-stroke deceleration.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ10X60-30
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.