Airtac MIJ Adjustable Cylinder MIJ32X10-10
The AirTAC Airtac MIJ Adjustable Cylinder MIJ32X10-10 is a genuine double acting, adjustable stroke round-body mini air cylinder with a Ø32mm bore and 10mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments.
- BoreØ32 mm
- Stroke10 mm
- Port size1/8"
- Acting typeDouble acting, adjustable stroke
- Rod threadM10×1.25
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ32X10-10
Dial in your forward end position precisely with the AirTAC MIJ32X10-10, a round-body stainless steel mini cylinder featuring a 10mm extend-stroke adjustment window. An external stop screw lets you shorten the forward travel by up to 10mm on-site, absorbing setup tolerances without swapping hardware. This double-acting actuator delivers 402.2 N of push force at 0.5 MPa, yielding a safe working load of roughly 241 N or a 20.5 kg vertical lift with a 2:1 margin.
Built with a riveted stainless barrel and Ø12mm rod, it resists mild corrosion and washdown environments. The unit operates at 30-800 mm/s on a 1/8" port with an M10x1.25 male rod thread. Because this is a non-magnet SKU, it cannot host CMSG, DMSG or EMSG sensors. Fixed TPU bumper pads decelerate the stroke end, and the stop screw functions purely as an end-position setter, not a mid-stroke lock.
Airtac MIJ Adjustable Cylinder MIJ32X10-10 Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ32X10-10 |
|---|---|
| Series | MIJ mini cylinder |
| Bore size | Ø32 mm |
| Stroke | 10 mm |
| Acting type | Double acting, adjustable stroke |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G. Note: the Ø32 bore is a larger, non-ISO-6432 size.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | 484 N |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MIJ Adjustable Cylinder MIJ32X10-10
| MIJ | round-body mini cylinder (adjustable-stroke). |
|---|---|
| 32 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ32X10-10 Is Used
Precision Stop Gauging
Use the 10mm extend adjustment to fine-tune a mechanical stop for parts gauging, leveraging the 402.2 N push force to hold components firmly.
Transfer Diverter Setup
Trim the forward stroke on-site to accommodate different package widths on a conveyor line without changing out the entire actuator assembly.
Light Pressing Tasks
Apply a calculated 241 N safe working load for seating small bearings, using the external screw to control the exact forward end position.
Is the Airtac MIJ Adjustable Cylinder MIJ32X10-10 the Right Cylinder?
When sizing this 32mm bore, dropping down to an MIJ25X10-10 reduces the 0.5 MPa push force to 245.3 N, whereas stepping up to an MIJ40X10-10 raises it to 628.3 N. The 10mm adjustable forward stop is ideal for changeover jobs requiring slight position tweaks. Keep in mind the piston drifts on air loss, so install an external rod lock or pilot check valve for suspended loads. Mount via LB foot, FA flange or TC trunnion (SDB pivot-block is unavailable), and select an -S variant if you require position sensing.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ32X10-10 FAQ
This 32mm bore cylinder uses a 1/8" port. At 0.5 MPa it provides 402.2 N push and 345.6 N pull force. At 0.7 MPa it delivers 563 N push and 483.8 N pull. The theoretical maximum force is 82 kgf at 1.0 MPa.
An external stop screw shortens the extend stroke by up to 10mm on-site, while retract remains full. This SKU lacks a magnet, so it cannot accept CMSG, DMSG or EMSG sensors. The stainless build resists mild corrosion, and fixed TPU bumpers cushion the stroke end.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ32X10-10
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.