Airtac MIJ Adjustable Cylinder MIJ32X80-10
The AirTAC Airtac MIJ Adjustable Cylinder MIJ32X80-10 is a genuine double acting, adjustable stroke round-body mini air cylinder with a Ø32mm bore and 80mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments.
- BoreØ32 mm
- Stroke80 mm
- Port size1/8"
- Acting typeDouble acting, adjustable stroke
- Rod threadM10×1.25
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ32X80-10
Dial in your forward end position on-site with the AirTAC MIJ32X80-10, a double-acting round-body mini cylinder featuring a stainless-steel barrel and rod for mild washdown resistance. An external stop screw lets you shorten the extend stroke by up to 10 mm, covering a 70-80 mm usable forward range without swapping parts. The retract stroke remains full length.
This Ø32 mm bore delivers substantial force, pushing with 402.2 N and pulling with 345.6 N at 0.5 MPa. For motion planning, this translates to a safe working load of roughly 241 N or a vertical lift capacity of about 20.5 kg with a 2:1 margin. It uses a 1/8" port and a male M10x1.25 rod thread. Note that this SKU lacks a magnet, so it cannot accept CMSG/DMSG/EMSG sensors.
Airtac MIJ Adjustable Cylinder MIJ32X80-10 Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ32X80-10 |
|---|---|
| Series | MIJ mini cylinder |
| Bore size | Ø32 mm |
| Stroke | 80 mm |
| Acting type | Double acting, adjustable stroke |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G. Note: the Ø32 bore is a larger, non-ISO-6432 size.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | 484 N |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MIJ Adjustable Cylinder MIJ32X80-10
| MIJ | round-body mini cylinder (adjustable-stroke). |
|---|---|
| 32 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ32X80-10 Is Used
Precision Gauging Stops
Use the 10 mm extend adjustment to fine-tune the contact position for varying part widths, applying up to 402.2 N of push force to hold components securely during measurement.
Staged Diverting Arms
Trim the forward stroke on-site to accommodate different package sizes on a washdown-resistant stainless line, ensuring positive diversion without over-travel.
Tooling Changeover Blocks
Leverage the adjustable end position to set multiple mechanical stops for rapid machine changeovers, relying on the 241 N safe working load to position tooling accurately.
Is the Airtac MIJ Adjustable Cylinder MIJ32X80-10 the Right Cylinder?
When sizing this actuator, step down to the Ø25 bore if your application only requires 245.3 N of push force at 0.5 MPa, or step up to the Ø40 bore for 628.3 N when heavier payloads are involved. The 10 mm external stop screw is ideal for taking up mechanical tolerances during setup or accommodating minor part variations, letting one part number serve multiple stop positions.
Keep in mind the fixed TPU bumper pads only decelerate the piston near the stroke end; they do not function as a mid-stroke lock. The piston will drift on air loss, so install an external rod lock or pilot check valve for held loads. Mount using LB foot, FA flange, or TC trunnion brackets, as the SDB pivot block is not available for this adjustable variant.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ32X80-10 FAQ
This double-acting cylinder uses a 1/8" port and generates a push force of 402.2 N and a pull force of 345.6 N at 0.5 MPa. At 0.7 MPa, push increases to 563 N and pull to 483.8 N. The theoretical maximum force is 82 kgf at 1.0 MPa.
An external stop screw shortens the extend stroke by up to 10 mm on-site, allowing you to set the exact forward end position between 70 and 80 mm. The retract stroke remains full length. This SKU has no magnet (-S variant required for CMSG/DMSG/EMSG sensors) and uses fixed TPU bumper pads rather than an adjustable air cushion.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ32X80-10
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.