Airtac SAID50 Double Rod Cylinder SAID50AX60S
The AirTAC Airtac SAID50 Double Rod Cylinder SAID50AX60S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø50mm bore and 60mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ50 mm
- Stroke60 mm
- Port sizeG1/4
- Acting typeDouble acting
- Rod threadM16×1.5
- CushionAdjustable, 30 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SAID50 Double Rod Cylinder SAID50AX60S
The AirTAC SAID50X60-S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 50mm bore and 60mm stroke. Because the twin rods occupy both sides of the piston, the annulus area is identical in each direction, yielding an equal extend and retract force of 825N at 0.5 MPa. A rod protrudes from both end covers, allowing you to mount the primary workpiece on one end and a cam or position flag on the opposite end.
This specific variant includes a SUS420J2 stainless steel rod (code A) for enhanced corrosion resistance and is equipped with a magnet (-S) for position sensing. It utilizes PT tapered ports and integrates adjustable air cushions at both ends to decelerate the piston near stroke limits. The extruded aluminum barrel features sensor grooves on both sides, compatible with AirTAC CMSE reed and DMSE electronic solid-state switches.
Airtac SAID50 Double Rod Cylinder SAID50AX60S Technical Specifications
| Model | Airtac SAID50 Double Rod Cylinder SAID50AX60S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 60 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
Theoretical Output Force (Ø50mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SAID50 Double Rod Cylinder SAID50AX60S
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 50 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SAID50 Double Rod Cylinder SAID50AX60S Is Used
Symmetric Force Transfer
Ideal for mechanisms requiring identical push and pull dynamics, utilizing the equal annulus area to deliver 825N of force seamlessly in both directions.
Dual-Side Tooling Actuation
Mount the primary workpiece on the front rod and a secondary cam or limit flag on the rear rod to trigger external sensors or secondary mechanisms simultaneously.
Anti-Rotation Slides
The twin-rod architecture prevents the load from twisting or rotating under offset stresses, providing superior guidance compared to a single-rod cylinder.
Is the Airtac SAID50 Double Rod Cylinder SAID50AX60S the Right Cylinder?
Choose this 50mm twin-rod actuator when an application demands equal push and pull forces, superior anti-rotation guidance, or dual-side actuation. If your mechanism requires less force, stepping down to the 40mm bore yields 528N both ways at 0.5 MPa; if you need more power, the 63mm bore provides 1402N. Unlike a single-rod SAI, this double-rod design prevents the load from twisting under offset stresses.
As a dimensionally interchangeable ISO 15552 cylinder, it serves as a drop-in replacement for other standard profile double-rod cylinders. It uses the reduced SAID mounting accessory set (Basic, FA, LB, TC, FTC, TCM1, TCM2), omitting the FB, CA, CB, and CR brackets found on single-rod variants. Note that this cylinder does not hold its load if air pressure is lost; for position holding without live pressure, consider the SAIL or BSAID series. At 60mm stroke, side-load bending is minimal, but external guides are recommended for heavy radial loads.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SAID50 Double Rod Cylinder SAID50AX60S FAQ
It provides an equal force of 825N in both the extend and retract directions at 0.5 MPa (1154N at 0.7 MPa). This equal both-way force is the primary advantage of the double-rod design.
Yes, it is dimensionally interchangeable per ISO 15552 profile standards. However, it uses a reduced mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2) and omits the FB, CA, CB, and CR brackets designed for single-rod cylinders.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SAID50 Double Rod Cylinder SAID50AX60S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.