Airtac SAUD Double Rod Cylinder SAUD40X45
The AirTAC Airtac SAUD Double Rod Cylinder SAUD40X45 is a genuine double-acting profile-type standard air cylinder with a Ø40mm bore and 45mm stroke, 1/4" air ports and adjustable end cushioning. Its hard-anodized aluminum-profile barrel is shorter than an ISO 15552 cylinder of the same bore, and it shares SC-series mounting accessories.
- BoreØ40 mm
- Stroke45 mm
- Port size1/4"
- Acting typeDouble acting
- Rod threadM12×1.25
- CushionAdjustable, 21 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SAUD Double Rod Cylinder SAUD40X45
The AirTAC SAUD40X45 is a double-acting, double-rod profile cylinder featuring a 40 mm bore and a 45 mm stroke. A rod protrudes from both ends, meaning both faces use the rod-side piston area. This yields exactly 528 N of output force at 0.5 MPa in both directions. The extruded hard-anodized aluminum barrel keeps the body shorter than an ISO 15552 unit of the same bore.
Because of the twin-rod architecture, the rear extension can drive a second tool or act as a cam. This specific SKU lacks the -S magnet option, so it cannot host CMSG or DMSG reed sensors. Operating speed spans 30-800 mm/s, and the 1/4" port drives air efficiently. For sizing, a safe working load is roughly 317 N (60% of the 528 N figure), translating to a 27 kg vertical lift capacity with a 2:1 safety margin.
Airtac SAUD Double Rod Cylinder SAUD40X45 Technical Specifications
| Model | Airtac SAUD Double Rod Cylinder SAUD40X45 |
|---|---|
| Series | SAU profile-type cylinder |
| Bore size | Ø40 mm |
| Stroke | 45 mm |
| Acting type | Double acting |
| Port size | 1/4" |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 21 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAU series datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G (BSPP). A high-temperature seal (0-150 °C) is available.
Theoretical Output Force (Ø40mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SAUD Double Rod Cylinder SAUD40X45
| SAU | Profile-type standard cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×45 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAU-family variants: SAUD (double rod), SAUJ (adjustable stroke), SAUF (with built-in solenoid valve), and SAU-S with built-in magnet. Seals: TPU (blank) / Viton H / NBR N. Sensor switches: CMSG / DMSG / EMSG.
Where the Airtac SAUD Double Rod Cylinder SAUD40X45 Is Used
Twin-Tool Transfer
Drives two synchronized pick-and-place grippers simultaneously from a single compact body, ensuring perfectly matched timing without external linkages.
Anti-Rotation Lift
Lifts light platforms up to 27 kg vertically with inherent twist resistance, preventing the load from rotating during transit without external linear bearings.
Dual-End Cam Trip
Uses the protruding rear rod to mechanically trip a limit switch at mid-stroke, providing a hard mechanical position signal independent of pneumatic sensors.
Is the Airtac SAUD Double Rod Cylinder SAUD40X45 the Right Cylinder?
Choose this 40 mm bore if you need 528 N of equal bidirectional thrust at 0.5 MPa. Stepping down to a 32 mm bore drops the equal force to 345 N, while stepping up to a 50 mm bore raises it to 825 N. A double-rod design is the right call when your mechanism demands anti-rotation guidance, synchronized twin-tool driving, or needs a rear extension to trip an external switch. Mounting is limited to Basic, FA flange, and LB foot styles, matching the AirTAC SC series. Since this SKU lacks a magnet, you cannot mount magnetic sensors. At a 45 mm stroke, side loads are minimal, but always use external guides for longer strokes over 300 mm.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB — same as SC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SAUD Double Rod Cylinder SAUD40X45 FAQ
The force is equal in both directions because it is a double-rod cylinder. It outputs 528 N at 0.5 MPa, 739 N at 0.7 MPa, and 950 N at 0.9 MPa. The 1/4" port and 16 mm rod ensure balanced thrust on both strokes.
No, the adjustable 21 mm air cushions only decelerate the piston near the stroke ends; they do not act as a brake. For load holding, you must install an external rod lock or a pilot-operated check valve.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SAUD Double Rod Cylinder SAUD40X45
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.