Airtac SDAD Double Rod Slim Cylinder SDAD16X15S
The AirTAC Airtac SDAD Double Rod Slim Cylinder SDAD16X15S is a genuine double-acting COMPACT cylinder with a piston rod out BOTH ends (Ø16mm bore, 15mm stroke). The through-rod resists twisting and lets you drive a tool on one end while a switch or dog reads position on the other — with identical force in both directions.
- BoreØ16 mm
- Stroke15 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod
- Rod threadM3×0.5 (F) / M5×0.8 (B)
- CushionFixed NBR bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SDAD Double Rod Slim Cylinder SDAD16X15S
The AirTAC SDAD16X15S is a compact double-acting cylinder with a piston rod exiting both ends of its riveted body. Because a rod occupies each chamber, the annular area is identical on extend and retract, yielding an equal push and pull force of 86.4 N at 0.5 MPa. This symmetry is a major advantage when driving loads that must not bias to one side.
The through-rod geometry resists twisting and lets you mount a work tool on one end while fitting a dog or switch on the opposite end. Its short body saves axial mounting depth where a larger profile cylinder will not fit. The built-in magnet (-S) supports AirTAC reed or electronic switches, and end shock is absorbed by a fixed NBR bumper.
Airtac SDAD Double Rod Slim Cylinder SDAD16X15S Technical Specifications
| Model | Airtac SDAD Double Rod Slim Cylinder SDAD16X15S |
|---|---|
| Series | SDAD compact double-rod cylinder |
| Bore size | Ø16 mm |
| Stroke | 15 mm |
| Acting type | Double acting, rod both ends |
| Port size | M5×0.8 |
| Rod end thread | M3×0.5 female / M5×0.8 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
| Max standard stroke | Up to 50 mm |
Because a rod occupies both cylinder chambers, the effective area — and therefore the force — is identical in both directions. Specifications follow the official AirTAC SDAD datasheet.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
Force uses the annular (rod-side) area on both strokes, so extend and retract match. Actual usable force is lower than theoretical due to friction. Size with a safety margin.
Model Code: Airtac SDAD Double Rod Slim Cylinder SDAD16X15S
| SDAD | Compact double-acting cylinder, rod out both ends. |
|---|---|
| 16 | Bore size in mm. |
| ×15 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch sensing (omit = none). |
| B | Male-thread piston rods (omit = female thread). |
Thread: PT standard. Related SDA-family variants: SDA (single rod), SSA/STA (single acting), SDAJ (adjustable stroke), SDAT (duplex), SDAW (duplex-end).
Where the Airtac SDAD Double Rod Slim Cylinder SDAD16X15S Is Used
Shuttle Transfer
Pushes and pulls a light parts shuttle with equal 86.4 N force, ensuring consistent timing in both directions without load bias.
Gripper Jaw Sync
Drives an opposing gripper jaw from one end while the opposite rod end mounts a dog to trigger a reed or electronic switch.
Guide Pin Feed
Feeds a delicate guide pin into a fixture; the through-rod resists twisting to keep the pin perfectly aligned during insertion.
Is the Airtac SDAD Double Rod Slim Cylinder SDAD16X15S the Right Cylinder?
When sizing this 16 mm bore, compare it both ways: the smaller SDAD12 yields 42.4 N at 0.5 MPa, while the larger SDAD20 provides 131.9 N. The 86.4 N output here gives a safe working load of roughly 52 N (about 60 percent of capacity) and a vertical lift capability near 4.4 kg with a 2:1 safety margin. Choose this model when those figures match your symmetric load requirement.
The through-rod prevents rotation and enables dual-end mounting. Confirm your bore needs 15 mm of travel, an M5x0.8 air port, and female M3x0.5 rod-end threads. Note that a plain cylinder drifts on air loss or valve centering—the fixed NBR bumper only decelerates near stroke end, so add an external rod lock or pilot-operated check valve for load holding.
Quick checklist
- ✓ Need equal force both directions?
- ✓ Anti-rotation / dual-end mounting?
- ✓ Space for a rod that exits both ends
- ✓ Port/thread type (PT)
- ✓ Magnet (S) for sensors?
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Leave clearance for the rod exiting both ends.
- check Avoid side load on either rod end.
- check Front/rear covers are riveted — do not dismantle.
- check Installation by qualified personnel per AirTAC docs.
Airtac SDAD Double Rod Slim Cylinder SDAD16X15S FAQ
Because the double-rod design provides equal annular area in both directions, push and pull forces are identical: 86.4 N at 0.5 MPa, 121 N at 0.7 MPa, and a theoretical maximum of 18 kgf at 1.0 MPa.
The through-rod resists twisting and allows you to mount a tool on one end and a position dog on the other. The short riveted body also saves axial depth, and the included magnet works with AirTAC reed or electronic switches.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SDAD Cylinders
Request a Quote for Airtac SDAD Double Rod Slim Cylinder SDAD16X15S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.