Airtac SDAD Double Rod Slim Cylinder SDAD16X50SB
The AirTAC Airtac SDAD Double Rod Slim Cylinder SDAD16X50SB is a genuine double-acting COMPACT cylinder with a piston rod out BOTH ends (Ø16mm bore, 50mm stroke). The through-rod resists twisting and lets you drive a tool on one end while a switch or dog reads position on the other — with identical force in both directions.
- BoreØ16 mm
- Stroke50 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod
- Rod threadM3×0.5 (F) / M5×0.8 (B)
- CushionFixed NBR bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SDAD Double Rod Slim Cylinder SDAD16X50SB
The AirTAC SDAD16X50SB is a compact double-acting cylinder featuring a 6 mm through-rod exiting both ends of its riveted body. Because a rod occupies each chamber, the annular area is identical on extend and retract, yielding exactly 86.4 N of push and pull force at 0.5 MPa. This symmetry prevents asymmetric loading on delicate mechanisms.
Equipped with a built-in magnet (-S) for AirTAC reed or electronic switches and male M5x0.8 rod threads (-B) on both ends, it operates at 30-500 mm/s. End-of-stroke energy is managed solely by a fixed NBR bumper, which decelerates the piston rather than locking it.
Airtac SDAD Double Rod Slim Cylinder SDAD16X50SB Technical Specifications
| Model | Airtac SDAD Double Rod Slim Cylinder SDAD16X50SB |
|---|---|
| Series | SDAD compact double-rod cylinder |
| Bore size | Ø16 mm |
| Stroke | 50 mm |
| Acting type | Double acting, rod both ends |
| Port size | M5×0.8 |
| Rod end thread | M3×0.5 female / M5×0.8 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
| Max standard stroke | Up to 50 mm |
Because a rod occupies both cylinder chambers, the effective area — and therefore the force — is identical in both directions. Specifications follow the official AirTAC SDAD datasheet.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
Force uses the annular (rod-side) area on both strokes, so extend and retract match. Actual usable force is lower than theoretical due to friction. Size with a safety margin.
Model Code: Airtac SDAD Double Rod Slim Cylinder SDAD16X50SB
| SDAD | Compact double-acting cylinder, rod out both ends. |
|---|---|
| 16 | Bore size in mm. |
| ×50 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch sensing (omit = none). |
| B | Male-thread piston rods (omit = female thread). |
Thread: PT standard. Related SDA-family variants: SDA (single rod), SSA/STA (single acting), SDAJ (adjustable stroke), SDAT (duplex), SDAW (duplex-end).
Where the Airtac SDAD Double Rod Slim Cylinder SDAD16X50SB Is Used
Symmetric Transfer Jaws
Drives a gripper on one male rod end while the opposite end pushes an identical 86.4 N load, keeping the 50 mm stroke perfectly balanced.
Anti-Twist Pin Insertion
The 6 mm through-rod resists rotational twist during downward part seating, ensuring the male M5x0.8 tool stays aligned without lateral drift.
Dual-End Component Pusher
Mounts a dog on the rear rod to trigger an electronic switch while the front rod indexes a lightweight 4.4 kg fixture across a 50 mm gap.
Is the Airtac SDAD Double Rod Slim Cylinder SDAD16X50SB the Right Cylinder?
When sizing this 16 mm bore, compare its 86.4 N @0.5 MPa output against the smaller SDAD12 at 42.4 N and the larger SDAD20 at 131.9 N. The through-rod geometry resists twisting and permits mounting a work tool on one male M5x0.8 end while a switch tracks position on the opposite side. A safe working load is roughly 52 N (about 60% of the 0.5 MPa figure), translating to a 4.4 kg vertical lift with a 2:1 margin.
This unit includes the -S magnet for sensing and the -B male rod threads. It uses an M5x0.8 port. Remember that a plain cylinder drifts when air is lost or a valve centers; the NBR bumper only decelerates near stroke end. For load holding without live pressure, install an external rod lock or pilot-operated check valve.
Quick checklist
- ✓ Need equal force both directions?
- ✓ Anti-rotation / dual-end mounting?
- ✓ Space for a rod that exits both ends
- ✓ Port/thread type (PT)
- ✓ Magnet (S) for sensors?
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Leave clearance for the rod exiting both ends.
- check Avoid side load on either rod end.
- check Front/rear covers are riveted — do not dismantle.
- check Installation by qualified personnel per AirTAC docs.
Airtac SDAD Double Rod Slim Cylinder SDAD16X50SB FAQ
Because the double-rod design provides equal annular area in both directions, push and pull forces are identical: 86.4 N at 0.5 MPa, 121 N at 0.7 MPa, and a theoretical maximum of 18 kgf at 1.0 MPa.
Yes. The -B option provides male M5x0.8 threads on both rod ends for dual-end tooling, while the -S built-in magnet allows you to track position with AirTAC reed or electronic switches along the body grooves.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SDAD Cylinders
Request a Quote for Airtac SDAD Double Rod Slim Cylinder SDAD16X50SB
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.