Airtac SDAD Double Rod Slim Cylinder SDAD32X25S
The AirTAC Airtac SDAD Double Rod Slim Cylinder SDAD32X25S is a genuine double-acting COMPACT cylinder with a piston rod out BOTH ends (Ø32mm bore, 25mm stroke). The through-rod resists twisting and lets you drive a tool on one end while a switch or dog reads position on the other — with identical force in both directions.
- BoreØ32 mm
- Stroke25 mm
- Port sizePT1/8
- Acting typeDouble acting, double rod
- Rod threadM6×1.0 (F) / M10×1.25 (B)
- CushionFixed NBR bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SDAD Double Rod Slim Cylinder SDAD32X25S
The AirTAC SDAD32X25S is a 32mm bore, double-acting compact cylinder featuring a 25mm stroke and a through-rod that exits both ends of the riveted body. Because the rod occupies both chambers, the annular area is identical in each direction, meaning push force equals pull force at 345.6 N under 0.5 MPa. This symmetric output is ideal for balanced actuation tasks.
Equipped with a built-in piston magnet (-S), this unit supports AirTAC reed or electronic switches for end-of-stroke sensing via the body grooves. The short footprint saves axial mounting depth compared to standard profile cylinders. End-of-travel deceleration is handled by a fixed NBR bumper, yielding a stable speed range of 30-500 mm/s across an operating pressure span of 0.15 to 1.0 MPa.
Airtac SDAD Double Rod Slim Cylinder SDAD32X25S Technical Specifications
| Model | Airtac SDAD Double Rod Slim Cylinder SDAD32X25S |
|---|---|
| Series | SDAD compact double-rod cylinder |
| Bore size | Ø32 mm |
| Stroke | 25 mm |
| Acting type | Double acting, rod both ends |
| Port size | PT1/8 |
| Rod end thread | M6×1.0 female / M10×1.25 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
| Max standard stroke | Up to 120 mm |
Because a rod occupies both cylinder chambers, the effective area — and therefore the force — is identical in both directions. Specifications follow the official AirTAC SDAD datasheet.
Theoretical Output Force (Ø32mm)
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
Force uses the annular (rod-side) area on both strokes, so extend and retract match. Actual usable force is lower than theoretical due to friction. Size with a safety margin.
Model Code: Airtac SDAD Double Rod Slim Cylinder SDAD32X25S
| SDAD | Compact double-acting cylinder, rod out both ends. |
|---|---|
| 32 | Bore size in mm. |
| ×25 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch sensing (omit = none). |
| B | Male-thread piston rods (omit = female thread). |
Thread: PT standard. Related SDA-family variants: SDA (single rod), SSA/STA (single acting), SDAJ (adjustable stroke), SDAT (duplex), SDAW (duplex-end).
Where the Airtac SDAD Double Rod Slim Cylinder SDAD32X25S Is Used
Gripper Jaw Actuation
Drives synchronous gripper jaws where equal push and pull forces of 345.6 N prevent twisting during part clamping.
Dual-End Transfer Pusher
Mounts a pusher plate on one rod end and a magnetic dog on the other to trigger an electronic switch mid-cycle.
PCB Board Lifting
Lifts delicate electronics vertically with a 17.6 kg safe margin, using the anti-rotation rod to maintain precise coplanar alignment.
Is the Airtac SDAD Double Rod Slim Cylinder SDAD32X25S the Right Cylinder?
When sizing this 32mm bore, evaluate your neighbors: the SDAD25 provides 206.2 N at 0.5 MPa, while the SDAD40 offers 527.8 N at 0.5 MPa. The SDAD32X25S provides a safe working load of roughly 207 N (about 60% of its 345.6 N capacity) and can vertically lift approximately 17.6 kg with a 2:1 safety margin. The through-rod design resists twisting and permits mounting a tool on one end and a position dog on the opposite side.
This configuration features a 12mm rod diameter, female M6x1.0 rod-end threads, and a PT1/8 port. Note that a plain cylinder drifts when air is lost or the valve centers; the fixed NBR bumper only decelerates near stroke end and does not function as a lock. For load holding without live pressure, integrate an external rod lock or pilot-operated check valve.
Quick checklist
- ✓ Need equal force both directions?
- ✓ Anti-rotation / dual-end mounting?
- ✓ Space for a rod that exits both ends
- ✓ Port/thread type (PT)
- ✓ Magnet (S) for sensors?
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Leave clearance for the rod exiting both ends.
- check Avoid side load on either rod end.
- check Front/rear covers are riveted — do not dismantle.
- check Installation by qualified personnel per AirTAC docs.
Airtac SDAD Double Rod Slim Cylinder SDAD32X25S FAQ
The double-rod design yields equal force in both directions: 345.6 N at 0.5 MPa and 483.8 N at 0.7 MPa. The theoretical maximum is 70 kgf at 1.0 MPa, with a proof pressure of 1.5 MPa.
Yes, the through-rod exits both sides to resist rotation and allow dual-end tooling. The -S magnet works with AirTAC reed or electronic switches in the body grooves to confirm stroke endpoints.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SDAD Cylinders
Request a Quote for Airtac SDAD Double Rod Slim Cylinder SDAD32X25S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.