Airtac SDAD Double Rod Slim Cylinder SDAD32X65S
The AirTAC Airtac SDAD Double Rod Slim Cylinder SDAD32X65S is a genuine double-acting COMPACT cylinder with a piston rod out BOTH ends (Ø32mm bore, 65mm stroke). The through-rod resists twisting and lets you drive a tool on one end while a switch or dog reads position on the other — with identical force in both directions.
- BoreØ32 mm
- Stroke65 mm
- Port sizePT1/8
- Acting typeDouble acting, double rod
- Rod threadM6×1.0 (F) / M10×1.25 (B)
- CushionFixed NBR bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SDAD Double Rod Slim Cylinder SDAD32X65S
The AirTAC SDAD32X65S is a double-acting, double-rod compact cylinder featuring a 32 mm bore and 65 mm stroke. Because the 12 mm piston rod exits both ends of the riveted body, the annular areas match perfectly, yielding identical push and pull forces of 345.6 N at 0.5 MPa. This symmetric output is ideal for driving loads without inducing directional bias.
The through-rod geometry inherently resists twisting, allowing you to mount a work tool on one end and a position dog on the opposite side simultaneously. End-of-stroke deceleration is handled by a fixed NBR bumper rather than an adjustable air cushion. The built-in magnet (-S) supports AirTAC reed or electronic switches via the body sensor grooves.
Airtac SDAD Double Rod Slim Cylinder SDAD32X65S Technical Specifications
| Model | Airtac SDAD Double Rod Slim Cylinder SDAD32X65S |
|---|---|
| Series | SDAD compact double-rod cylinder |
| Bore size | Ø32 mm |
| Stroke | 65 mm |
| Acting type | Double acting, rod both ends |
| Port size | PT1/8 |
| Rod end thread | M6×1.0 female / M10×1.25 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
| Max standard stroke | Up to 120 mm |
Because a rod occupies both cylinder chambers, the effective area — and therefore the force — is identical in both directions. Specifications follow the official AirTAC SDAD datasheet.
Theoretical Output Force (Ø32mm)
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
Force uses the annular (rod-side) area on both strokes, so extend and retract match. Actual usable force is lower than theoretical due to friction. Size with a safety margin.
Model Code: Airtac SDAD Double Rod Slim Cylinder SDAD32X65S
| SDAD | Compact double-acting cylinder, rod out both ends. |
|---|---|
| 32 | Bore size in mm. |
| ×65 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch sensing (omit = none). |
| B | Male-thread piston rods (omit = female thread). |
Thread: PT standard. Related SDA-family variants: SDA (single rod), SSA/STA (single acting), SDAJ (adjustable stroke), SDAT (duplex), SDAW (duplex-end).
Where the Airtac SDAD Double Rod Slim Cylinder SDAD32X65S Is Used
Symmetric Transfer Chuck
Equal 345.6 N push and pull forces securely grip and release a transfer chuck without directional force bias, ensuring smooth part handoff.
Anti-Rotation Edge Guide
The dual-exit through-rod resists twisting during high-speed web guiding, maintaining precise alignment while a dog triggers an electronic switch on the opposite end.
Vertical Lift Stopper
Lifting a 17.6 kg payload with a 2:1 margin is safely managed in both directions, with the fixed NBR bumper absorbing the end-of-stroke shock.
Is the Airtac SDAD Double Rod Slim Cylinder SDAD32X65S the Right Cylinder?
When sizing this 32 mm bore, compare its 345.6 N @0.5 MPa capacity against adjacent models: the SDAD25 provides 206.2 N, while the SDAD40 offers 527.8 N. A practical safe working load is roughly 207 N (about 60% of the 0.5 MPa figure), translating to a vertical lift of approximately 17.6 kg with a 2:1 safety margin. This specific unit includes the -S magnet for reed or electronic sensing and uses a PT1/8 port.
Remember that a plain double-rod cylinder drifts when air pressure is lost or the valve is centered; the fixed NBR bumper only decelerates near the stroke end and cannot hold a load. For vertical or suspended loads requiring position holding without live pressure, you must integrate an external rod lock or a pilot-operated check valve.
Quick checklist
- ✓ Need equal force both directions?
- ✓ Anti-rotation / dual-end mounting?
- ✓ Space for a rod that exits both ends
- ✓ Port/thread type (PT)
- ✓ Magnet (S) for sensors?
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Leave clearance for the rod exiting both ends.
- check Avoid side load on either rod end.
- check Front/rear covers are riveted — do not dismantle.
- check Installation by qualified personnel per AirTAC docs.
Airtac SDAD Double Rod Slim Cylinder SDAD32X65S FAQ
The double-rod design provides equal force in both directions: 345.6 N at 0.5 MPa and 483.8 N at 0.7 MPa. The theoretical maximum is 70 kgf at 1.0 MPa. Operating pressure ranges from 0.15 to 1.0 MPa.
Yes. The through-rod extends from both ends, allowing you to drive a tool on one side while mounting a dog for a reed or electronic switch on the other. This model includes the -S magnet required for position sensing.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SDAD Cylinders
Request a Quote for Airtac SDAD Double Rod Slim Cylinder SDAD32X65S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.