Airtac SDAD Double Rod Slim Cylinder SDAD80X65S
The AirTAC Airtac SDAD Double Rod Slim Cylinder SDAD80X65S is a genuine double-acting COMPACT cylinder with a piston rod out BOTH ends (Ø80mm bore, 65mm stroke). The through-rod resists twisting and lets you drive a tool on one end while a switch or dog reads position on the other — with identical force in both directions.
- BoreØ80 mm
- Stroke65 mm
- Port sizePT3/8
- Acting typeDouble acting, double rod
- Rod threadM14×1.5 (F) / M22×1.5 (B)
- CushionFixed NBR bumper (both ends)
About the Airtac SDAD Double Rod Slim Cylinder SDAD80X65S
The AirTAC SDAD80X65S is a double-acting, double-rod compact cylinder featuring a 80 mm bore and 65 mm stroke. Because the piston rod exits both ends, the annular area remains identical in each chamber, yielding equal push and pull forces of 2267.8 N at 0.5 MPa. This symmetric thrust is perfect for balanced actuation. The short riveted body conserves axial mounting depth where larger profile cylinders cannot fit.
Equipped with a built-in magnet (-S), this unit supports AirTAC reed or electronic switches for position sensing. The 25 mm through-rod resists twisting during operation. End-of-stroke deceleration relies on a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion. Operating speed ranges from 30-500 mm/s.
Airtac SDAD Double Rod Slim Cylinder SDAD80X65S Technical Specifications
| Model | Airtac SDAD Double Rod Slim Cylinder SDAD80X65S |
|---|---|
| Series | SDAD compact double-rod cylinder |
| Bore size | Ø80 mm |
| Stroke | 65 mm |
| Acting type | Double acting, rod both ends |
| Port size | PT3/8 |
| Rod end thread | M14×1.5 female / M22×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
| Max standard stroke | Up to 120 mm |
Because a rod occupies both cylinder chambers, the effective area — and therefore the force — is identical in both directions. Specifications follow the official AirTAC SDAD datasheet.
Theoretical Output Force (Ø80mm)
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 2268 N |
| 0.7 MPa | 3175 N |
| Max (@1.0 MPa) | 463 kgf |
Force uses the annular (rod-side) area on both strokes, so extend and retract match. Actual usable force is lower than theoretical due to friction. Size with a safety margin.
Model Code: Airtac SDAD Double Rod Slim Cylinder SDAD80X65S
| SDAD | Compact double-acting cylinder, rod out both ends. |
|---|---|
| 80 | Bore size in mm. |
| ×65 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch sensing (omit = none). |
| B | Male-thread piston rods (omit = female thread). |
Thread: PT standard. Related SDA-family variants: SDA (single rod), SSA/STA (single acting), SDAJ (adjustable stroke), SDAT (duplex), SDAW (duplex-end).
Where the Airtac SDAD Double Rod Slim Cylinder SDAD80X65S Is Used
Symmetric Lift Station
Employs the equal 2267.8 N bidirectional force to raise and lower heavy platens without stroke imbalance, ensuring level vertical positioning.
Anti-Twist Guide
Leverages the 25 mm through-rod to resist torsional deflection during precision pressing, maintaining strict tool alignment without extra guides.
Dual-End Transfer
Drives a workpiece clamp on the front rod while mounting a magnetic dog on the rear extension to trigger an electronic sensor for timing.
Is the Airtac SDAD Double Rod Slim Cylinder SDAD80X65S the Right Cylinder?
When sizing this model, consider the adjacent bores: stepping down to the SDAD63 provides 1401.5 N at 0.5 MPa, while stepping up to the SDAD100 yields 3524.9 N. The SDAD80X65S offers a safe working load of roughly 1361 N (about 60% of its 0.5 MPa rating) and can vertically lift approximately 115.6 kg with a 2:1 safety margin.
This configuration includes the -S magnet for sensing and female M14x1.5 rod-end threads on both ends, supplied by a PT3/8 port. The through-rod geometry prevents rotation and allows mounting a dog on the opposite end from your tool. Note that a plain cylinder drifts when air is lost; use an external rod lock or pilot-operated check valve for load holding.
Quick checklist
- ✓ Need equal force both directions?
- ✓ Anti-rotation / dual-end mounting?
- ✓ Space for a rod that exits both ends
- ✓ Port/thread type (PT)
- ✓ Magnet (S) for sensors?
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Leave clearance for the rod exiting both ends.
- check Avoid side load on either rod end.
- check Front/rear covers are riveted — do not dismantle.
- check Installation by qualified personnel per AirTAC docs.
Airtac SDAD Double Rod Slim Cylinder SDAD80X65S FAQ
The force is equal in both directions due to the double-rod design: 2267.8 N at 0.5 MPa, 3175 N at 0.7 MPa, and a theoretical maximum of 463 kgf at 1.0 MPa. The maximum operating pressure is 1.0 MPa.
Yes, the through-rod extends from both sides, allowing you to drive a tool on one end and mount a switch dog on the other. The -S magnet enables position detection with AirTAC reed or electronic switches.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SDAD Cylinders
Request a Quote for Airtac SDAD Double Rod Slim Cylinder SDAD80X65S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.