Airtac SED Double Rod Cylinder SED40X700S
The AirTAC Airtac SED Double Rod Cylinder SED40X700S is a genuine double-acting ISO 15552 double-rod cylinder: a Ø16mm piston rod exits BOTH ends of the Ø40mm bore, giving equal force and speed in both directions and letting you mount tooling or a sensor flag on the back rod. Stroke 700mm, PT1/4 ports, adjustable cushioning.
- BoreØ40 mm
- Stroke700 mm
- Port sizePT1/4
- ConfigurationDouble rod
- Rod threadM12×1.25
- CushionAdjustable, 30 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SED Double Rod Cylinder SED40X700S
The AirTAC SED40X700S is a double-acting, double-rod profile cylinder conforming to the ISO 15552 interface. Because a 16 mm rod exits both ends, the annular piston area is symmetrical, generating an equal 528 N of thrust in both directions at 0.5 MPa. The extruded aluminum barrel omits external tie rods, and adjustable air cushioning at both ends decelerates the load near stroke end.
Equipped with a standard -S magnet, this unit supports CMSE reed and DMSE electronic sensors for end-of-stroke detection. The rear rod protrusion allows you to mount a cam or secondary flag, driving an independent mechanism while guiding the load against rotation.
Airtac SED Double Rod Cylinder SED40X700S Technical Specifications
| Model | Airtac SED Double Rod Cylinder SED40X700S |
|---|---|
| Series | SED ISO 15552 double-rod cylinder |
| Bore size | Ø40 mm |
| Stroke | 700 mm |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SED datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø40mm)
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
Because a rod exits both ends, the effective piston area — and therefore the force — is identical on extend and retract. Actual usable force is lower than theoretical; size with a safety margin.
Model Code: Airtac SED Double Rod Cylinder SED40X700S
| SED | ISO 15552 profile-barrel DOUBLE-ROD double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×700 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SED): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SE (single rod), SEJ (double-rod adjustable stroke), BSED (double-rod rod lock).
Where the Airtac SED Double Rod Cylinder SED40X700S Is Used
Web Guiding Mechanisms
Provides 528 N of equal bidirectional force to steer and tension material webs, using the rear rod to mount a cam for dancer-arm feedback.
Dual-End Transfer Pushers
Drives long-stroke package transfer arms with 739 N at 0.7 MPa, utilizing the through-rod design to prevent binding over 700 mm of travel.
Mirror Film Roll Splicers
Actuates splicing blades from both ends simultaneously, ensuring perfectly parallel cuts across wide webs without rotational drift.
Is the Airtac SED Double Rod Cylinder SED40X700S the Right Cylinder?
For a 700 mm stroke, the SED40X700S delivers 528 N both ways at 0.5 MPa. If your payload is lighter, step down to the 32 mm bore (345 N both ways); if heavier, step up to the 50 mm bore (825 N both ways). At this stroke length, external guide rails are strongly recommended to prevent side-load deflection on the 16 mm rods.
Choose this double-rod layout over a single-rod SE when you need anti-rotation stability or rear-rod tooling. Remember that the air cushion decelerates but does not hold position on air loss; for fail-safe holding, select a BSED rod-lock cylinder. To replace an ISO 15552 unit, match the 40 mm bore, 700 mm stroke, PT1/4 port, and mounting style (Basic, FA, LB, TC, FTC, TCM1, or TCM2).
Quick checklist
- ✓ Equal force/speed both directions needed?
- ✓ Back-rod space for tooling or a flag
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Support both rod ends; avoid side load.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SED Double Rod Cylinder SED40X700S FAQ
The SED40X700S delivers equal force in both directions due to its double-rod design: 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
The twin rods provide superior anti-rotation guidance and allow the rear rod to drive a secondary mechanism or sensor flag. It drops into any standard ISO 15552 mounting footprint using Basic, FA, LB, TC, FTC, TCM1, or TCM2 accessories.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SED Cylinders
Request a Quote for Airtac SED Double Rod Cylinder SED40X700S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.