Airtac SGCJ125~160 Adjustable Cylinder SGCJ160X450-50S
The AirTAC Airtac SGCJ125~160 Adjustable Cylinder SGCJ160X450-50S is a genuine double acting, adjustable stroke ISO 15552 (orig. ISO 6431) tie-rod air cylinder with a Ø160mm bore and 450mm stroke, G3/4 air ports and adjustable end cushioning. Its large-bore tie-rod build delivers high thrust and drops into standardized ISO 15552 mounting on heavy automation.
- BoreØ160 mm
- Stroke450 mm
- Port sizeG3/4
- Acting typeDouble acting, adjustable stroke
- Rod threadM36×2.0
- CushionAdjustable, 50 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SGCJ125~160 Adjustable Cylinder SGCJ160X450-50S
Delivering 10053 N of push force at 0.5 MPa, this large-bore ISO 15552 tie-rod cylinder integrates four steel rods clamping the aluminum barrel for maximum structural rigidity. The built-in piston magnet supports CMSG, DMSG, and EMSG switches for precise position detection, while the G3/4 air port feeds the 40 mm rod to generate 14074 N at 0.7 MPa.
An external adjuster allows you to shorten the extend stroke on-site by up to 50 mm, meaning the usable forward travel spans 400 to 450 mm without swapping the cylinder. This on-site tuning is ideal for matching shared spares across stroke variants. The mechanism sets the end position but does not lock the load, as the 50 mm adjustable air cushions only decelerate the piston. For vertical lifting, it safely handles around 512 kg with a 2:1 margin, and a Viton H seal option extends operation up to 150 C.
Airtac SGCJ125~160 Adjustable Cylinder SGCJ160X450-50S Technical Specifications
| Model | Airtac SGCJ125~160 Adjustable Cylinder SGCJ160X450-50S |
|---|---|
| Series | SGC ISO 15552 tie-rod cylinder |
| Bore size | Ø160 mm |
| Stroke | 450 mm |
| Acting type | Double acting, adjustable stroke |
| Port size | G3/4 |
| Rod thread | M36×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 50 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC SGC datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Thread options: PT (blank) / G. TPU seals are not available for the Ø250 bore (NBR / Viton only).
Theoretical Output Force (Ø160mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 10053 N | 9425 N |
| 0.7 MPa | 14074 N | — |
| Max (@1.0 MPa) | 2050 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SGCJ125~160 Adjustable Cylinder SGCJ160X450-50S
| SGCJ | ISO 15552 tie-rod cylinder (adjustable-stroke type). |
|---|---|
| 160 | Bore size in mm (125 / 160 / 200 / 250). |
| ×450 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
SGC-family variants: SGC (double acting), SGCD (double rod), SGCJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / FTC / TCM1 / TCM2. Seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SGCJ125~160 Adjustable Cylinder SGCJ160X450-50S Is Used
Press Tonnage Calibration
Use the 50 mm extend-shortening window to precisely set the bottom dead center on a light assembly press without machining new spacers.
Pallet Stopper Alignment
Fine-tune the stopping position of 500 kg pallets on a conveyor by adjusting the stroke end on-site to match varying load depths.
Vertical Lift Dampening
Lift approximately 512 kg of raw material safely, relying on the 50 mm adjustable air cushions to decelerate the heavy load before the end of travel.
Is the Airtac SGCJ125~160 Adjustable Cylinder SGCJ160X450-50S the Right Cylinder?
When sizing this unit against neighboring bores, the 125 mm version provides 6136 N of push at 0.5 MPa, while the 200 mm bore steps up to 15708 N, placing this 160 mm model perfectly in the middle for medium-to-heavy loads. The 50 mm adjustable window is highly beneficial when you need to fine-tune the end position on-site or maintain a single spare part across multiple stroke variants. You can mount it using FA, LB, TC, FTC, TCM1, or TCM2 hardware. The included -S magnet enables CMSG, DMSG, and EMSG sensor tracking. Because the 450 mm stroke exceeds 500 mm when fully extended, ensure you use a external guide to prevent rod side-loading and premature seal wear.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Long-stroke side load — support the rod end
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load; support long strokes at the rod end.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SGCJ125~160 Adjustable Cylinder SGCJ160X450-50S FAQ
At 0.5 MPa it provides 10053 N of push and 9425 N of pull. At 0.7 MPa the push is 14074 N and the pull is 13194 N. The theoretical maximum force is 2050 kgf at 1.0 MPa. It uses a G3/4 air port and a 40 mm piston rod.
The 450 mm nominal stroke is the maximum travel. The external adjuster lets you shorten the extend stroke by up to 50 mm on-site, giving a usable range of 400 to 450 mm. The retract end remains fixed, and this adjustment sets the end position rather than locking the load.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Made to Order
Large-bore cylinders built to order — confirm lead time.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SGC Cylinders
Request a Quote for Airtac SGCJ125~160 Adjustable Cylinder SGCJ160X450-50S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.