Airtac ACED Double-acting Compact Cylinder ACED80X200B
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED80X200B is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø80mm bore and 200mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ80 mm
- Stroke200 mm
- Port size1/8"
- Acting typeDouble acting, double rod
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED80X200B
A double acting compact cylinder built to ISO 21287, the ACED80X200B pushes a 20 mm rod out of BOTH covers, so thrust is identical on every stroke: 2356.2 N at 0.5 MPa and 3298.7 N at 0.7 MPa, equal in each direction because both sides work on the rod-side area. The male rod thread (B code) bolts straight to your tooling, and air enters through 1/8" ports. The hard-anodized aluminium body carries magnet slots along its full length, and the S45C hard-chrome plated rod shrugs off wear on high-cycle lines.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it drops into tight press fixtures and gantry frames a full-length body cannot enter. A fixed TPU bumper at each end absorbs end-of-stroke shock, and the through-rod resists rotation and side load while the rear rod can carry a sensor flag. Run it on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), 30-500 mm/s, -20 to +70 C. Note this unit has no magnet fitted; order the optional -S code if you need CMSE / DMSE switch positions.
Airtac ACED Double-acting Compact Cylinder ACED80X200B Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED80X200B |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø80 mm |
| Stroke | 200 mm |
| Acting type | Double acting, double rod |
| Port size | 1/8" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø80mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 2356 N |
| 0.7 MPa | 3299 N |
| Max (@1.0 MPa) | 481 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED80X200B
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 80 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED80X200B Is Used
Press fixture ejection
The 2356.2 N through-rod kicks formed brackets out of a stamping die from either side, with the 200 mm stroke clearing a deep die pocket in a compact press frame.
Conveyor pusher gates
A packaging line uses the double rod to divert cartons at 30-500 mm/s; the symmetric rod keeps the pusher plate square without extra guides.
Pallet clamp arms
Clamping arms on a palletizing cell grip loads with 3298.7 N at 0.7 MPa, the rear rod carrying a flag for a proximity sensor on the return stroke.
Is the Airtac ACED Double-acting Compact Cylinder ACED80X200B the Right Cylinder?
Size up or down from here: the ACED50X200 delivers 881.2 N at 0.5 MPa for lighter clamping, while the ACED100X200 reaches 3769.9 N for heavier press work. This 80 mm bore sits in the middle with 2356.2 N both ways. Remember the piston drifts when air is lost, so add a rod lock or pilot check if the load must stay put. FA/FB flanges, LB feet and FTC brackets bolt to the standard ISO 21287 face, and I/Y rod knuckles suit the male thread. No magnet is fitted on this code; specify -S if CMSE / DMSE position sensing is planned.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED80X200B FAQ
Because a rod exits both covers, force is equal in both directions: 2356.2 N at 0.5 MPa and 3298.7 N at 0.7 MPa on every stroke, with a maximum of 480.5 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, and the 1/8" port matches the 80 mm bore.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it fits shallow jigs and guards. A fixed TPU bumper at each end absorbs end-of-stroke shock. This code has no magnet, so no switch can be read; order the optional -S version to enable CMSE / DMSE sensors on the body slots. FA/FB flange, LB foot and FTC mounts bolt straight on.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED80X200B
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.