This model is discontinued
AirTAC has phased out the MALD series. You can still order this code here: we ship the direct replacement MBLD32X250S, with the same bore, stroke, output force, port and mounting, so it fits the same application. The MBLD replacement upgrades to a riveted rolling-packed body and CMSG / DMSG / EMSG sensors (the MAL used CS1-M / DS1-M).
Airtac MALD Aluminum Alloy Mini Cylinder MALD32X250-S
The AirTAC Airtac MALD Aluminum Alloy Mini Cylinder MALD32X250-S is a double-acting, double-rod aluminum mini cylinder: a rod exits both ends of the Ø32mm bore, so push and pull force are equal. This model is discontinued — the direct replacement is the MBLD32X250-S, matching bore, stroke, force and mounting.
- BoreØ32 mm
- Stroke250 mm
- Port sizeG1/8
- Acting typeDouble acting, double rod
- Rod threadM10×1.25
- StatusDiscontinued → MBLD32X250-S
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MALD Aluminum Alloy Mini Cylinder MALD32X250-S
The AirTAC MALD32X250-S is a discontinued double-acting, double-rod mini cylinder. A rod exits both ends, yielding equal force in both directions at 346 N each way at 0.5 MPa. The direct replacement is the MBLD32X250-S, matching the 32 mm bore, 250 mm stroke, G1/8 port, and mounting.
This unit features a 12 mm hard-chrome carbon steel rod with an M10x1.25 end thread. Unlike single-rod types, the twin rods resist rotation and double the bearing load for guided slides. The older MAL uses threaded covers and a CS1-M / DS1-M magnet switch, whereas the MBLD upgrade features a riveted rolling-packed body and CMSG / DMSG / EMSG sensors. It relies on a fixed rubber bumper, not an adjustable cushion.
Airtac MALD Aluminum Alloy Mini Cylinder MALD32X250-S Technical Specifications
| Model | Airtac MALD Aluminum Alloy Mini Cylinder MALD32X250-S |
|---|---|
| Series | MALD double-rod mini cylinder (discontinued) |
| Replacement | MBLD32X250-S |
| Bore size | Ø32 mm |
| Stroke | 250 mm |
| Acting type | Double acting, double rod |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.1 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed rubber bumper |
| Max standard stroke | Up to 500 mm |
Double-rod types have no back-cover code and no SDB pivot; mount on the body, LB foot or FA flange. The MBLD32X250-S carries the same ratings.
Output Force — Equal Both Ways (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | 484 N |
| Max (@1.0 MPa) | 70 kgf | |
A rod exits both ends, so the effective area — and force — is equal in both directions. The MBLD32X250-S matches these values.
Model Code: Airtac MALD Aluminum Alloy Mini Cylinder MALD32X250-S
| MALD | Double-rod aluminum mini cylinder, double acting (discontinued). |
|---|---|
| 32 | Bore size in mm (20/25/32/40). |
| ×250 | Stroke length in mm. |
| S | Optional magnet for a CS1-M / DS1-M sensor (MBLD uses CMSG/DMSG/EMSG). |
Replacement: MALD → MBLD. No back-cover (CA/U/CM) and no SDB on double-rod. Mounting: LB / FA.
Where the Airtac MALD Aluminum Alloy Mini Cylinder MALD32X250-S Is Used
PCB Edge-Guiding Slide
Drives a guided edge-guide for PCB conveyors. The twin rods prevent yaw during the 250 mm travel, while the 346 N equal force ensures consistent lateral pressure.
Textile Beam Lifter
Raises and lowers textile warp beams using both rod ends. The symmetrical 484 N force at 0.7 MPa keeps the lifting platform perfectly level without mechanical binding.
Dual-End Pneumatic Ejector
Ejects molded plastic parts from a press. The rear rod simultaneously trips a mechanical cam, using the 70 kgf maximum force to positively knock out the part.
Replacing the Airtac MALD Aluminum Alloy Mini Cylinder MALD32X250-S with MBLD32X250-S
To replace the MALD32X250-S, specify the MBLD32X250-S and confirm the 32 mm bore, 250 mm stroke, G1/8 port, PT thread, and FA or LB mounting (there is no back cover or SDB option). Retain the -S magnet, but note the sensor family changes from CS1-M / DS1-M to CMSG / DMSG / EMSG. Size using the equal push and pull force of 346 N at 0.5 MPa. If you need less force, step down to the 25 mm bore (206 N at 0.5 MPa); for more force, step up to the 40 mm bore (528 N at 0.5 MPa). At 250 mm stroke, minimize side-load by guiding the load externally to prevent rod binding.
Upgrade checklist
- ✓ Order the MBLD32X250-S (same bore/stroke/force)
- ✓ Force equal both ways (346 N at 0.5 MPa)
- ✓ Twin rods for anti-rotation / rear flag
- ✓ No back cover / SDB — plan a body or FA/LB mount
- ✓ Sensor: swap CS1-M/DS1-M → CMSG/DMSG/EMSG
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.1 – 1.0 MPa operating pressure.
- check Protect both rod ends from side load on long strokes.
- check No back-cover / SDB on double-rod — use body / FA / LB.
- check Front/rear covers are threaded — not for field disassembly.
- check For new builds, specify the MBLD32X250-S instead of this discontinued model.
Airtac MALD Aluminum Alloy Mini Cylinder MALD32X250-S FAQ
Yes, the MALD32X250-S is discontinued. The direct replacement is the MBLD32X250-S, which matches the 32 mm bore, 250 mm stroke, G1/8 port, and force. You will need to upgrade your sensors from CS1-M / DS1-M to CMSG / DMSG / EMSG.
Because it is a double-rod cylinder, the push and pull forces are equal: 346 N at 0.5 MPa and 484 N at 0.7 MPa, with a maximum force of 70 kgf at 1.0 MPa. It uses a fixed rubber bumper at the end of stroke, not an adjustable cushion, and cannot hold a load on air loss.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
Direct Upgrade
The MBLD32X250-S replaces this model 1:1.
Fast Dispatch
MBLD replacements are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Recommended AirTAC MBLD Replacements
Request a Quote (Airtac MALD Aluminum Alloy Mini Cylinder MALD32X250-S → MBLD32X250-S)
Tell us the quantity and destination — we quote the direct MBLD32X250-S replacement with price, stock and lead time, usually within 7-8 hours.