Airtac PC Threaded Straight Connector PC1001D
The AirTAC Airtac PC Threaded Straight Connector PC1001D is a genuine male connector for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale connector
- SeriesPC
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PC Threaded Straight Connector PC1001D
The AirTAC PC1001D is a PC series one-touch male connector, AirTAC's standard straight push-in fitting for mounting a Dia 10 mm tube directly onto a 1/8 in PT male thread. You push the tube home and the stainless spring gasket and chuck grip it against the POM chuck seat; press the release ring and the tube slides straight back out. On the PC range the D suffix changes the release button to black while the body stays the standard brass straight-connector pattern, so it matches visually when buttons need to stand out on a crowded manifold.
This is the resin and brass spec profile, not the metal BP line: working pressure 0-1.0 MPa, negative pressure down to -750 mmHg (10 Torr), proof pressure 1.5 MPa and a working temperature of -20 to +70 C. The thread arrives with sealant pre-applied, so it seals on PT threads without extra tape, and it runs on soft nylon or polyurethane tube only.
Airtac PC Threaded Straight Connector PC1001D Technical Specifications
| Model | Airtac PC Threaded Straight Connector PC1001D |
|---|---|
| Type | Male connector |
| Series | PC |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PC Threaded Straight Connector PC1001D
| PC | Male connector. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PC Threaded Straight Connector PC1001D Is Used
Valve manifold outlets
A 1/8 in PT outlet on a solenoid valve manifold is the classic home for this fitting: a 10 mm drop line carries sensible volume to downstream cylinders without the restriction of an 8 mm branch.
Case-erector packaging lines
On carton erecting and taping machines, case clamp and flap-fold cylinders are commonly plumbed in 10 mm tube; a straight male connector at the valve or cylinder port keeps the run short and serviceable.
Pneumatic clamping on CNC fixtures
Fixture clamp circuits on machining centres often run 10 mm lines from a 1/8 in ported control block; the push-in connector lets a technician swap a damaged clamp line in seconds without thread sealant work.
Is the Airtac PC Threaded Straight Connector PC1001D the Right Part?
On the 1/8 in PC thread ladder this sits between PC801 (Dia 8 tube, same thread) below and PC1201 (Dia 12 tube, same thread) above. Stepping down to Dia 8 gives you a slimmer, higher-velocity line for small actuators; stepping up to Dia 12 cuts pressure drop on longer runs. If your port is 1/4 in instead, PC1002 carries the same Dia 10 tube on a bigger thread. Note that 1/8 in is the smallest thread AirTAC offers on Dia 10 in this series - the M5 option stops at Dia 6. Tube OD must match exactly: a Dia 10 chuck will not seal on 3/8 in or 1/2 in tube, whatever the thread size.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PC Threaded Straight Connector PC1001D FAQ
Working pressure 0-1.0 MPa (0-10 kgf/cm2); negative pressure -750 mmHg (10 Torr); proof pressure 1.5 MPa; working temperature -20 to +70 C. It joins Dia 10 mm soft nylon or polyurethane tube to a 1/8 in PT male thread, with a black POM release button on the standard PC brass body.
No - the PC is a straight thread-to-tube connector, not a panel-mount part. For a Dia 10 tube through a panel, use the PM bulkhead connector, which carries an M20x1 locknut thread at this tube size; the PC1001D then continues the line on the downstream side.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PC Threaded Straight Connector PC1001D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.