Airtac PEB T-Shaped Straight Thread Tee Connector PEB1001
The AirTAC Airtac PEB T-Shaped Straight Thread Tee Connector PEB1001 is a genuine male branch tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale branch tee
- SeriesPEB
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PEB T-Shaped Straight Thread Tee Connector PEB1001
The PEB1001 is an AirTAC PEB male branch tee, a one-touch push-in fitting that splits a Dia 10 mm tube line into two while presenting a male 1/8" PT branch thread. Push the soft nylon or polyurethane tube into the port and the internal chuck grips it under the stainless spring gasket; press the POM release ring and the tube slides free. The branch thread runs from a brass stud, and like every threaded part in this catalogue it arrives with sealant already applied, so it can be wound straight into the port.
This is the resin/brass one-touch family, not the metal BPC line: working pressure 0-1.0 MPa, vacuum to -750 mmHg, proof pressure 1.5 MPa, and a temperature window of -20 to +70 C. The tee body is PBT with an aluminium-alloy guide and an NBR O-ring doing the sealing. Dia 10 is the largest tube size the PEB prefix offers on a 1/8" port, which makes this SKU the top of its branch-thread ladder rather than a mid-size step.
Airtac PEB T-Shaped Straight Thread Tee Connector PEB1001 Technical Specifications
| Model | Airtac PEB T-Shaped Straight Thread Tee Connector PEB1001 |
|---|---|
| Type | Male branch tee |
| Series | PEB |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PEB T-Shaped Straight Thread Tee Connector PEB1001
| PEB | Male branch tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PEB T-Shaped Straight Thread Tee Connector PEB1001 Is Used
Splitting a drop on a packaging machine
On a cartoning line, one 10 mm drop from the main can feed both the case-erector grippers and the flap-tucking cylinder: the PEB1001 branches the line at the point of use without cutting or re-flaring tube.
Feeding two stations in an electronics assembly cell
A pick-and-place bench running vacuum cups and a small press cylinder from one supply can branch at the bench frame with this tee, keeping both tools on the same Dia 10 line length so response stays even.
Branch air to a conveyor gate along the run
Down a bottling conveyor, a diverter gate midway along the run needs its own feed. Tapping the 10 mm main with a PEB1001 at the gate avoids running a separate line back to the valve manifold.
Is the Airtac PEB T-Shaped Straight Thread Tee Connector PEB1001 the Right Part?
Stepping down, PEB801 gives the same 1/8" branch thread on Dia 8 tube and suits lighter sub-lines such as sensor air or small actuators; stepping up in tube on this thread is not possible, because Dia 10 is the biggest tube PEB supports at 1/8". If your branch line needs Dia 12 tubing, move to PEB1202 on a 1/4" thread instead. Remember the mating port matters too: the brass stud is 1/8" PT here, and PEB1002 in 1/4" is the neighbour when the manifold port is larger.
Match the tube exactly. A Dia 10 fitting will not seal on 3/8" (10 mm is close to but not the same as 12 mm), and it will not hold 1/4" (6 mm) tube at any pressure. Only soft nylon or polyurethane tube belongs in a one-touch port; steel or rigid tube defeats the chuck. If the run has to pass through a panel wall rather than branch off it, the PMF bulkhead connector is the shape to look at instead.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PEB T-Shaped Straight Thread Tee Connector PEB1001 FAQ
It is a male branch tee for Dia 10 mm tube with a 1/8" PT male branch thread. Working pressure is 0-1.0 MPa (0-10 kgf/cm2), vacuum to -750 mmHg, proof pressure 1.5 MPa, and operating temperature -20 to +70 C. It accepts soft nylon or polyurethane tube only, seals with an NBR O-ring and stainless spring gasket, and the brass stud ships with thread sealant applied.
No. One-touch chucks are made for one tube OD, so the PEB1001 grips Dia 10 mm tube on both tube ports and nothing else - 1/4" (6 mm) tube will not seal in it. For a change of diameter on a branch, use a different-diameter fitting from the PEG/PEW range or step the whole circuit up. If you need a smaller tube branch off this same 1/8" port, PEB801 (Dia 8) or PEB601 (Dia 6) are the made sizes.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PEB T-Shaped Straight Thread Tee Connector PEB1001
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.