Airtac PED T-Shaped Side Thread Tee Fitting PED1001D
The AirTAC Airtac PED T-Shaped Side Thread Tee Fitting PED1001D is a genuine male run tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale run tee
- SeriesPED
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PED T-Shaped Side Thread Tee Fitting PED1001D
PED1001D is an AirTAC PED male run tee from the resin one-touch range, joining a Dia 10 mm soft nylon or polyurethane tube to a 1/8 in PT male thread. On a run tee the male thread sits on the straight-through run, so air continues linearly past the fitting while a third, perpendicular tube port branches off at 90 degrees. That makes this shape the natural pick when you need to tap a pilot line, gauge or actuator feed out of a main supply run without redirecting it.
Push the tube firmly home and the internal chuck grips it for a pressure-tight seal; press the POM release ring and the tube frees off again for rework or re-routing. This threaded resin part is rated 0-1.0 MPa (0-10 kgf/cm2) working pressure, -750 mmHg (10 Torr) vacuum and 1.5 MPa proof pressure, over -20 to +70 C. The body is PBT on a brass stud, and the D suffix here means the black body option rather than the standard grey. Note that AirTAC ships every threaded part in this range with sealant already applied to the thread, so PED1001D seals straight into the port with no extra tape or paste.
Airtac PED T-Shaped Side Thread Tee Fitting PED1001D Technical Specifications
| Model | Airtac PED T-Shaped Side Thread Tee Fitting PED1001D |
|---|---|
| Type | Male run tee |
| Series | PED |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PED T-Shaped Side Thread Tee Fitting PED1001D
| PED | Male run tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PED T-Shaped Side Thread Tee Fitting PED1001D Is Used
CNC router panel tapping
Tee a 1/8 in pressure switch or regulator signal line off the main Dia 10 mm run behind the sheet-metal control panel, without breaking the straight feed to the spindle clamp cylinder.
Bottling line actuator branch
Run the Dia 10 mm supply straight through to the next station while branching a perpendicular feed to a rotary indexing actuator on the filler carousel.
Packaging machine gauge takeoff
Add a 1/8 in PT pressure gauge port into an existing 10 mm nylon line feeding the sealing jaws, using the inline run so the main flow to the valves stays undisturbed.
Is the Airtac PED T-Shaped Side Thread Tee Fitting PED1001D the Right Part?
Inside the PED 1/8 in row, Dia 10 is the top of the ladder - the size below is PED0801 (Dia 8 x 1/8 in), which saves space and slightly narrows the bore feeding your branch; stepping up in tube instead means moving to PED1002, which carries the same Dia 10 tube on a 1/4 in thread. Check the port before you order. If the thread belongs on the perpendicular branch rather than the run, compare the PEB male branch tee, which puts the male thread at 90 degrees to the through-flow. And whatever shape you land on, tube OD must match exactly: a Dia 10 chuck will not reliably hold 1/4 in (6.35 mm) tube, and only soft nylon or polyurethane tubing carries the one-touch rating.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PED T-Shaped Side Thread Tee Fitting PED1001D FAQ
PED1001D is a resin one-touch male run tee taking a Dia 10 mm tube on a 1/8 in PT male thread. Working pressure is 0-1.0 MPa (0-10 kgf/cm2), vacuum capability is -750 mmHg (10 Torr), proof pressure is 1.5 MPa, and the working temperature range is -20 to +70 C. It accepts soft nylon or polyurethane tubing only, and the D suffix denotes the black body version.
Both tee two tube ports off a male thread, but the thread position differs. On the PED male run tee the 1/8 in male thread is on the straight-through run, so the branch tube port is the perpendicular leg. On the PEB male branch tee the male thread sits on that perpendicular branch instead. Choose PED when the threaded device hangs inline on the main line, and PEB when the thread feeds the branch while the tube run passes straight through.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PED T-Shaped Side Thread Tee Fitting PED1001D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.