Airtac PED T-Shaped Side Thread Tee Fitting PED1202D-S
SUS304 stainless variant (-S)The AirTAC Airtac PED T-Shaped Side Thread Tee Fitting PED1202D-S is a genuine male run tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale run tee
- SeriesPED
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PED T-Shaped Side Thread Tee Fitting PED1202D-S
PED1202D-S is an AirTAC male run tee from the PED family: a 1/4in PT male stud on the run, with two Dia 12 mm one-touch tube ports in line and a third branch port, so a supply line can be teed without breaking the main run open. The D suffix is the black version of a part that ships grey as standard, and the -S suffix selects the SUS304 option. On the PED family that means the threaded STUD is stainless steel 304; the tee body itself stays PBT, so this is not a solid stainless fitting.
All three tube ports are one-touch: push soft nylon or PU tube home and the internal chuck grips it instantly; press the POM release ring and the tube frees off. This is the resin spec profile, not the metal 0.9 MPa / 150 C line: working pressure 0 to 1.0 MPa, proof pressure 1.5 MPa, temperature -20 to +70 C, and vacuum down to -750 mmHg (10 Torr). The 1/4in male thread arrives with sealant already applied, ready to wind straight into a PT port.
Airtac PED T-Shaped Side Thread Tee Fitting PED1202D-S Technical Specifications
| Model | Airtac PED T-Shaped Side Thread Tee Fitting PED1202D-S |
|---|---|
| Type | Male run tee |
| Series | PED |
| Connection | Push-in one-touch |
| Body material | Stainless steel 304 (-S variant) |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. Stainless (-S): SUS304 in place of brass - a solid SUS304 body on the PC and POC straight connectors, and a PBT body with a SUS304 stud on the elbow, tee and branch shapes. Working pressure, proof pressure and temperature are unchanged from the standard version. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PED T-Shaped Side Thread Tee Fitting PED1202D-S
| PED | Male run tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
| -S | Stainless-steel body. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PED T-Shaped Side Thread Tee Fitting PED1202D-S Is Used
Extrusion frame run tees
Teeing a Dia 12 mm main air run along a plastics extrusion frame, where condensation and coolants wet the fasteners and a plain brass stud would tarnish - the SUS304 stud and black PBT body keep the joint serviceable.
Plating shop valve manifolds
Screwing the 1/4in PT stud into a solenoid manifold above pick-and-place cylinders over acid dip tanks, where splash and fume attack ordinary plated threads and the stainless stud holds up.
Bottling line gate cylinders
Splitting a Dia 12 supply run on a bottling conveyor to feed gate and clamp cylinders in one move, saving a separate branch elbow plus union on the guard side of the machine.
Is the Airtac PED T-Shaped Side Thread Tee Fitting PED1202D-S the Right Part?
On the 1/4in row of the PED ladder, Dia 12 is the largest tube offered, so the only sibling below it is Dia 10 (PED1002), which suits lighter actuator loads and trims the fitting footprint. To carry more than Dia 12 you have to step the thread up to 3/8in (PED1203), since no larger tube exists on the 1/4in row. The chuck grips genuine Dia 12 mm OD tube only - it will not seal 1/2in hose or any near-size tube. If the tee actually needs to pass through a sheet-metal panel rather than sit on a manifold face, the PMF bulkhead connector is the shape built for that job.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PED T-Shaped Side Thread Tee Fitting PED1202D-S FAQ
Working pressure 0 to 1.0 MPa (0-10 kgf/cm2), negative pressure down to -750 mmHg (10 Torr), proof pressure 1.5 MPa, and a temperature range of -20 to +70 C. This SKU is the Dia 12 mm tube size on all three one-touch ports with a 1/4in PT male thread.
No. On the PED family the -S suffix puts SUS304 on the threaded stud only; the tee body is PBT, the chuck is POM, with a stainless spring gasket and NBR seal. A solid SUS304 body is offered on the PC and POC straight connectors instead. The pressure, vacuum and temperature ratings are identical to the standard grey version.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PED T-Shaped Side Thread Tee Fitting PED1202D-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.