Airtac PED T-Shaped Side Thread Tee Fitting PED402D
The AirTAC Airtac PED T-Shaped Side Thread Tee Fitting PED402D is a genuine male run tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale run tee
- SeriesPED
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PED T-Shaped Side Thread Tee Fitting PED402D
The AirTAC PED402D is a male run tee from AirTAC's resin one-touch fitting range. It joins two lengths of Dia 4 mm soft nylon or polyurethane tubing in a straight run and carries a 1/4 inch PT male thread off the middle of that run, so a single tapped port feeds two tube lines from one fitting. Push each tube home and the stainless spring gasket inside the chuck grips it; press the POM release ring against the body and the tube frees off again.
This is the standard resin/brass profile, not the hotter metal line: working pressure 0-1.0 MPa (0-10 kgf/cm2), vacuum down to -750 mmHg (10 Torr), proof pressure 1.5 MPa, and a temperature window of -20 to +70 C. The all-black body is not cosmetic-only; on the PED series the D suffix recolours the entire body, whereas on the PC and POC straight connectors it changes just the release button. The 1/4 inch thread arrives with sealant already applied, so it goes into the tapped port as delivered.
Airtac PED T-Shaped Side Thread Tee Fitting PED402D Technical Specifications
| Model | Airtac PED T-Shaped Side Thread Tee Fitting PED402D |
|---|---|
| Type | Male run tee |
| Series | PED |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PED T-Shaped Side Thread Tee Fitting PED402D
| PED | Male run tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PED T-Shaped Side Thread Tee Fitting PED402D Is Used
Cartoning machine vacuum pick circuit
On a small cartoner, the 1/4 inch tapping on the vacuum generator manifold screws this run tee straight in and splits the feed into two Dia 4 lines reaching left- and right-hand suction cups on the pick head.
Delta-style pick-and-place gantry
Compact delta robots route air along slim extrusion channels; a Dia 4 run tee lets one manifold branch feed both a gripper line and a part-blow-off nozzle, and the black body blends with dark machine covers.
Valve manifold spur inside a control panel
Behind a panel door with a valve island, this male run tee into a 1/4 inch port sends Dia 4 spurs to a pressure switch and a small pneumatic indicator without adding unions to the cabinet.
Is the Airtac PED T-Shaped Side Thread Tee Fitting PED402D the Right Part?
Dia 4 is the smallest tube size the PED series is made in, so there is no step below it; the next rung up is PED602 with a Dia 6 bore, which gives a touch more carrying capacity per pulse in low-flow circuits. On the thread side, 1/4 inch is the largest port that Dia 4 tube is offered with - the same 4 mm tube also exists as PED401 (1/8 inch) and PED4M5 (M5x0.8 with a sealing gasket) for smaller tappings. Keep the tube OD exact: a Dia 6 fitting will not seal on nominal 1/4 inch (6.35 mm) tube even though the numbers look close.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PED T-Shaped Side Thread Tee Fitting PED402D FAQ
It is a Dia 4 mm one-touch run tee with a 1/4 inch PT male thread in a black body. Working pressure 0-1.0 MPa (0-10 kgf/cm2), negative pressure down to -750 mmHg (10 Torr), proof pressure 1.5 MPa, operating temperature -20 to +70 C, for soft nylon or polyurethane tubing only.
On the PED the male thread continues one leg of the straight run, so the two tube ports face opposite directions and the flow path passes straight through the tee. On a PEB branch tee the thread stands at 90 degrees off the run like a spur. Pick PED where the ported connection sits in the through line, and PEB where the port hangs off the side of it.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PED T-Shaped Side Thread Tee Fitting PED402D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.