Airtac PED T-Shaped Side Thread Tee Fitting PED601D
The AirTAC Airtac PED T-Shaped Side Thread Tee Fitting PED601D is a genuine male run tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale run tee
- SeriesPED
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PED T-Shaped Side Thread Tee Fitting PED601D
The PED601D is an AirTAC PED male run tee, a one-touch fitting that keeps two Dia 6 mm tubes in a straight through-line and adds a third outlet on a 1/8 inch PT male stud. Because the run legs share one axis, the main line keeps a clear path while the branch feeds sideways at 90 degrees. Push the tube home and the internal chuck grips it; press the release ring and the tube slides out again.
This is the resin and brass profile, not the metal BP line: 0-1.0 MPa working pressure, 1.5 MPa proof pressure, -20 to +70 C, and vacuum to -750 mmHg (10 Torr). The 1/8in stud arrives with thread sealant already applied, so no PTFE tape is needed before installation. Note the colour code: on a PED the D suffix turns the whole body black, whereas on the PC and POC straight connectors it only changes the release button.
Airtac PED T-Shaped Side Thread Tee Fitting PED601D Technical Specifications
| Model | Airtac PED T-Shaped Side Thread Tee Fitting PED601D |
|---|---|
| Type | Male run tee |
| Series | PED |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PED T-Shaped Side Thread Tee Fitting PED601D
| PED | Male run tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PED T-Shaped Side Thread Tee Fitting PED601D Is Used
Twin-gripper gantry feed
A run tee split on a Dia 6 nylon line lets one 1/8in valve-manifold port supply the two small gripper cylinders of a pick-and-place module without buying an extra valve outlet.
Carton-sealer dust blow-off
On a packaging machine frame, the tee drops a Dia 6 branch off a straight Dia 6 run to feed a small air jet that clears dust from the flap before the sealing head closes.
Colour-coded lab test rig
The black body tags a separate circuit on a test bench, so technicians trace the black Dia 6 lines at a glance and never cross-connect a calibrated instrument loop.
Is the Airtac PED T-Shaped Side Thread Tee Fitting PED601D the Right Part?
Below this SKU sits the PED401 (Dia 4 on the same 1/8in stud) and above it the PED801 (Dia 8). Stepping up the bore gives each leg more passage area for heavier draw; stepping down suits compact actuators and shorter runs. On the thread side, the 1/8in ladder of a PED supports Dia 4, 6, 8 and 10 tube; step to 1/4in (PED602) when the receiving port is larger. Match the tubing exactly - a Dia 6 chuck will not seal on 1/4in tube, and undersized tube can blow out under pressure.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PED T-Shaped Side Thread Tee Fitting PED601D FAQ
Working pressure 0-1.0 MPa (0-10 kgf/cm2), negative pressure to -750 mmHg (10 Torr), proof pressure 1.5 MPa, and a temperature range of -20 to +70 C. The fitting takes Dia 6 mm soft nylon or polyurethane tubing and carries a 1/8 inch PT male thread.
No. The chuck grips a 6 mm outside-diameter tube only; 1/4in (6.35 mm) tube will not seat and can release under pressure. Use exact Dia 6 tubing, or move to the PED size that matches the tube you actually run. Also, the stud ships pre-coated with thread sealant, so extra PTFE tape is unnecessary.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PED T-Shaped Side Thread Tee Fitting PED601D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.