Airtac PED T-Shaped Side Thread Tee Fitting PED602D
The AirTAC Airtac PED T-Shaped Side Thread Tee Fitting PED602D is a genuine male run tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale run tee
- SeriesPED
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PED T-Shaped Side Thread Tee Fitting PED602D
The PED602D is an AirTAC PED male run tee in the black (D) colour option, which on this series changes the body as well as the button. It screws into a 1/4in PT male-threaded port and accepts Dia 6 mm soft nylon or polyurethane tube in all three stems. A run tee means the threaded leg sits in line with the through-run, so the main flow passes straight across the fitting while a third leg tees off at 90 degrees - useful when you want to keep a circuit running past a take-off point.
This is a resin/brass one-touch part, not the metal BP line: working pressure 0-1.0 MPa (0-10 kgf/cm2), vacuum to -750 mmHg, proof pressure 1.5 MPa, and a temperature window of -20 to +70 C. To connect, push the tube firmly into the chuck until it bottoms out; the stainless spring gasket and POM chuck grip it against the aluminium guide. Pressing the release ring frees the tube again. The 1/4in thread arrives with sealant pre-applied, so no extra tape is needed on the port.
Airtac PED T-Shaped Side Thread Tee Fitting PED602D Technical Specifications
| Model | Airtac PED T-Shaped Side Thread Tee Fitting PED602D |
|---|---|
| Type | Male run tee |
| Series | PED |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PED T-Shaped Side Thread Tee Fitting PED602D
| PED | Male run tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PED T-Shaped Side Thread Tee Fitting PED602D Is Used
Palletizer gripper circuit
Tee a Dia 6 branch off the main 1/4in run to feed a vacuum gripper line while the primary flow continues to the next station on the palletizing head.
CNC air-blast take-off
Mount in-line on a machine-tool air blast circuit so the chip-clearing nozzle branch can be isolated downstream without breaking the main supply run.
Screen-printing machine valve manifold
Piggy-back a Dia 6 pilot supply to a squeegee control valve directly off the existing 1/4in feed, using the straight-through run to keep the original circuit intact.
Is the Airtac PED T-Shaped Side Thread Tee Fitting PED602D the Right Part?
On the PED 1/4in row, Dia 6 sits between two neighbours that both exist: step down to PED402 to feed small pilot lines and compact actuators, or up to PED802 when the branch supplies a larger cylinder where the 6 mm bore would choke the flow - capacity tracks the tube bore, so an 8 mm run moves noticeably more air. If you need the take-off at the end of the line rather than mid-run, the PEB branch tee or an elbow such as the PL602 is the better shape.
Match the tube exactly: the chuck is machined for a 6 mm outside diameter and will not seal on 1/4in (6.35 mm) tube, even though the sizes look close. Check the port thread is PT before ordering - this catalogue documents PT only.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PED T-Shaped Side Thread Tee Fitting PED602D FAQ
Working pressure 0-1.0 MPa (0-10 kgf/cm2), proof pressure 1.5 MPa, vacuum capability down to -750 mmHg (10 Torr), operating temperature -20 to +70 C. The fitting joins Dia 6 mm soft nylon or polyurethane tube on all three legs to a 1/4in PT male thread, which arrives with sealant pre-applied. The D suffix gives it the black body variant of the standard grey PED.
No - a run tee (PED) puts the thread in line with the through-flow, with one 90 degree take-off. If your port is at the end of a line and you need two equal branches, choose the PEB male branch tee instead, or the PYB Y fitting for an angled split. All three share the same 0-1.0 MPa resin/brass ratings, so the choice is purely about plumbing geometry.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PED T-Shaped Side Thread Tee Fitting PED602D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.