Airtac PED T-Shaped Side Thread Tee Fitting PED602D-S
SUS304 stainless variant (-S)The AirTAC Airtac PED T-Shaped Side Thread Tee Fitting PED602D-S is a genuine male run tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale run tee
- SeriesPED
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PED T-Shaped Side Thread Tee Fitting PED602D-S
The PED602D-S is an AirTAC PED male run tee, a one-touch fitting that splits a Dia 6 mm supply line in the run of the tee while a 1/4in PT male stud screws into the port. Push the soft nylon or polyurethane tube home and the internal chuck grips it against the stainless spring gasket; press the POM release ring to free it again, so branches can be reworked without cutting tube. The -S suffix makes this the SUS304 variant of the family: on the PED tee the PBT body stays PBT (here in the D black colour) and it is the male stud that is stainless steel 304, so it is the screwed connection, not the body, that gains corrosion resistance.
This is resin one-touch territory, not the metal BP line: working pressure 0-1.0 MPa (0-10 kgf/cm2), vacuum to -750 mmHg (10 Torr), proof pressure 1.5 MPa and a -20 to +70 C service window. AirTAC supplies the stud with sealant already on the thread, so the 1/4in PT end goes straight into the port without extra tape. Run-tee geometry means the through path stays in line and the stud takes the branch, which keeps pressure loss at the junction lower than a sharp branch tee on the same line.
Airtac PED T-Shaped Side Thread Tee Fitting PED602D-S Technical Specifications
| Model | Airtac PED T-Shaped Side Thread Tee Fitting PED602D-S |
|---|---|
| Type | Male run tee |
| Series | PED |
| Connection | Push-in one-touch |
| Body material | Stainless steel 304 (-S variant) |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. Stainless (-S): SUS304 in place of brass - a solid SUS304 body on the PC and POC straight connectors, and a PBT body with a SUS304 stud on the elbow, tee and branch shapes. Working pressure, proof pressure and temperature are unchanged from the standard version. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PED T-Shaped Side Thread Tee Fitting PED602D-S
| PED | Male run tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
| -S | Stainless-steel body. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PED T-Shaped Side Thread Tee Fitting PED602D-S Is Used
Injection moulding ejector circuits
Tapping a Dia 6 run off the main supply to feed ejector or core-pull cylinders on a moulding machine, with the SUS304 stud standing up to humid, release-agent-laden plant air.
Bottling line rinsing and blow-off
Wash-adjacent zones on bottling and canning conveyors get splashed daily; the stainless 1/4in stud resists thread corrosion where a plain brass stud would pit and weep.
Twin air knife feed on a PCB cleaner
Splitting one Dia 6 feed into a through line plus a 1/4in-ported branch serving a second nozzle on an electronics cleaning station, where copper-free fasteners are preferred near the process.
Is the Airtac PED T-Shaped Side Thread Tee Fitting PED602D-S the Right Part?
On the PED ladder at 1/4in thread, this Dia 6 version sits between the PED402-S (Dia 4) below and the PED802-S (Dia 8) above. Stepping down to Dia 4 suits light pilot and sensing lines; stepping up to Dia 8 carries noticeably more volume for short cylinder cycles - pick by the bore of the tube your machine is plumbed with, because a one-touch fitting holds one OD only and a Dia 6 socket will not grip 1/4in (6.35 mm) tube.
Match the stud to the port: 1/4in PT on this SKU, with 1/8in and 3/8in among the sibling options AirTAC makes on this prefix. If your junction sits at a dead end and the whole flow must turn 90 degrees into the stud, a PEB branch tee or a PL male elbow is the better shape than this run tee.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PED T-Shaped Side Thread Tee Fitting PED602D-S FAQ
It is a PED male run tee in the Dia 6 mm one-touch size with a 1/4in PT male stud and SUS304 stud construction on a black PBT body. Working pressure is 0-1.0 MPa (0-10 kgf/cm2), it holds vacuum to -750 mmHg (10 Torr), proof pressure is 1.5 MPa, and the temperature range is -20 to +70 C. Use soft nylon or polyurethane tube of exactly 6 mm OD.
No. One-touch chucks are ground to a single outside diameter, so this fitting grips only 6 mm OD tube - 1/4in (6.35 mm) tube will neither seat nor seal. If your circuit is plumbed in 4 mm, order the PED402-S; for 8 mm tube that feeds larger cylinders faster, the PED802-S is the direct neighbour in the same 1/4in stud size.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PED T-Shaped Side Thread Tee Fitting PED602D-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.