Airtac PED T-Shaped Side Thread Tee Fitting PED603
The AirTAC Airtac PED T-Shaped Side Thread Tee Fitting PED603 is a genuine male run tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale run tee
- SeriesPED
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PED T-Shaped Side Thread Tee Fitting PED603
The PED603 is an AirTAC PED male run tee, a one-touch fitting whose straight-through run accepts 6 mm OD soft nylon or polyurethane tube on both legs, with a 3/8" male PT thread branching off the centre at 90 degrees. Push the tube into the chuck and the stainless spring gasket grips it for a sealed joint; press the POM release ring and the tube frees for rework. Unlike a branch tee, the run of a run tee passes in one straight line, so the main flow path is not turned through the body.
This is the resin and brass one-touch profile, not the metal line: working pressure 0-1.0 MPa (0-10 kgf/cm2), vacuum to -750 mmHg (10 Torr), proof pressure 1.5 MPa, temperature -20 to +70 C. The centre thread is a brass stud, the female-side body is PBT, and AirTAC ships the thread with sealant already applied, so additional tape is normally unnecessary. The M-sized threads in this catalogue do not use sealant - they seal with a gasket.
Airtac PED T-Shaped Side Thread Tee Fitting PED603 Technical Specifications
| Model | Airtac PED T-Shaped Side Thread Tee Fitting PED603 |
|---|---|
| Type | Male run tee |
| Series | PED |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PED T-Shaped Side Thread Tee Fitting PED603
| PED | Male run tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PED T-Shaped Side Thread Tee Fitting PED603 Is Used
Manifold take-off on a press clamp circuit
The 3/8" male branch threads straight into a valve manifold outlet while the 6 mm run continues on to a downstream clamp cylinder, keeping the main supply line unbroken.
Belt scraper actuator feed on packaging lines
A 6 mm polyurethane drop from the machine's supply rail runs through the PED603 to feed a small scraper or reject-push cylinder, with the tee's straight run carrying air to the next station.
Lab automation pick-and-place vacuum circuit
Rated to -750 mmHg (10 Torr), the run tee suits a vacuum ejector branch on a benchtop dispense or pick-and-place cell, where the 3/8" port mounts the ejector and the 6 mm run loops to further cups.
Is the Airtac PED T-Shaped Side Thread Tee Fitting PED603 the Right Part?
At the 3/8" thread position, Dia 6 is the smallest tube the PED ladder offers - Dia 4 is simply not made at this thread, so if your circuit runs 4 mm tube you must step the thread down to 1/8" or 1/4" instead. Stepping up in bore gives you the PED803 (8 mm tube, 3/8" thread), and the thread itself has two neighbours on the PED603 run: PED602 (1/4") and PED604 (1/2"). The run tee shape is the right answer when a line should continue straight past a take-off point; if the line itself must turn 90 degrees into the wall, an PL male elbow does that job instead. Whichever you pick, the tube OD must match the fitting exactly - a Dia 6 chuck will not hold 1/4" (6.35 mm) imperial tube.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PED T-Shaped Side Thread Tee Fitting PED603 FAQ
It is an AirTAC PED male run tee joining Dia 6 mm tube on the run to a 3/8" male PT thread on the branch. Working pressure is 0-1.0 MPa (0-10 kgf/cm2), it draws vacuum down to -750 mmHg (10 Torr), proof pressure is 1.5 MPa, and the temperature range is -20 to +70 C. Use soft nylon or polyurethane tube of exactly 6 mm OD. The release button and chuck are POM, the guide is aluminium alloy, the spring gasket is stainless, the O-ring is NBR, and the stud is brass.
No for most cases - AirTAC applies sealant to the male thread at the factory, so the fitting can be screwed straight into the port. Inspect the coating and re-tape only if it has been damaged. Note that this applies to the threaded sizes only; the M5 versions of the PED series seal with a gasket instead and must never receive sealant.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PED T-Shaped Side Thread Tee Fitting PED603
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.