Airtac PED T-Shaped Side Thread Tee Fitting PED603D
The AirTAC Airtac PED T-Shaped Side Thread Tee Fitting PED603D is a genuine male run tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale run tee
- SeriesPED
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PED T-Shaped Side Thread Tee Fitting PED603D
The PED603D is an AirTAC PED male run tee, a three-port one-touch fitting in which the 3/8in male thread sits in line with the run and a Dia 6 tube socket branches off at 90 degrees. Push the 6mm soft nylon or polyurethane tubing into each socket until it bottoms out: the internal chuck grips the tube wall and the stainless spring gasket plus NBR O-ring seal it. Pressing the POM release ring frees the tube again. Threaded ports of this size arrive with sealant already applied, so the 3/8in PT thread seals straight into the port.
This is the resin and brass one-touch profile, rated 0-1.0 MPa (0-10 kgf/cm2), with a proof pressure of 1.5 MPa, vacuum capability down to -750 mmHg and a working temperature of -20 to +70 C. The D suffix here gives the fitting a black body rather than the standard grey, which matters on machines where dark housings and black cable dressings dominate. Note that Dia 6 is the smallest tube size AirTAC makes for the 3/8in PED, so this SKU sits at the fine end of the bore ladder for this thread.
Airtac PED T-Shaped Side Thread Tee Fitting PED603D Technical Specifications
| Model | Airtac PED T-Shaped Side Thread Tee Fitting PED603D |
|---|---|
| Type | Male run tee |
| Series | PED |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PED T-Shaped Side Thread Tee Fitting PED603D
| PED | Male run tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PED T-Shaped Side Thread Tee Fitting PED603D Is Used
Pick-and-place gantry feed
Use the 3/8in run to carry supply along a gantry beam while the Dia 6 branch drops down to a compact vacuum ejector or parallel gripper, keeping the arm's plumbing to a single light tube.
Dark-panel packaging machines
The black body of the D suffix blends with the black guards and cable trunking typical of stainless-clad packaging lines, so the tee stays visually invisible at an in-line 3/8in drop point.
Workshop air drop to a bench clamp
Screw the 3/8in PT thread into a drop-leg regulator outlet and run 6mm polyurethane to a bench-mounted clamp cylinder, with the tee's in-line port continuing the run to a second station.
Is the Airtac PED T-Shaped Side Thread Tee Fitting PED603D the Right Part?
On the 3/8in PED row AirTAC offers Dia 6, 8, 10 and 12, so there is no tube size below this one at this thread - if your circuit runs finer than 6mm, step down to a 1/4in thread instead, where the PED602 pairs the same Dia 6 bore with a smaller port. Stepping up to the PED803 gives a Dia 8 bore and noticeably more capacity through the same 3/8in port, at the cost of a larger release collar and a stiffer minimum bend radius on the tubing.
Match the 3/8in PT thread to the port drawing before ordering: an oversize thread forced into a 1/4in tapped hole will not seal with the factory-applied sealant. And remember that one-touch tube OD must match exactly - a Dia 6 socket will not grip 1/4in (6.35mm) or 8mm tube, and mixing inch and metric tubing is the most common cause of leaks on converted circuits.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PED T-Shaped Side Thread Tee Fitting PED603D FAQ
Working pressure 0-1.0 MPa (0-10 kgf/cm2), proof pressure 1.5 MPa, negative pressure down to -750 mmHg (10 Torr), and a temperature range of -20 to +70 C. The part is a male run tee joining Dia 6mm soft nylon or polyurethane tubing to a 3/8in PT male thread, finished in black (D suffix). These figures belong to the resin and brass one-touch profile - they are not the 0.9 MPa / 150 C metal BPC ratings.
No. One-touch chucks are sized to a single exact tube OD, and 1/4in nominal tube measures 6.35mm, which the Dia 6 chuck will not seal or grip reliably. Use genuine 6mm OD soft nylon or polyurethane tubing, or select a fitting in the imperial N-series instead. Also note that on the 3/8in PED, Dia 6 is the smallest tube AirTAC offers - there is no Dia 4 option at this thread.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PED T-Shaped Side Thread Tee Fitting PED603D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.