Airtac PED T-Shaped Side Thread Tee Fitting PED801
The AirTAC Airtac PED T-Shaped Side Thread Tee Fitting PED801 is a genuine male run tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale run tee
- SeriesPED
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PED T-Shaped Side Thread Tee Fitting PED801
The PED801 is an AirTAC PED male run tee, a resin one-touch fitting that keeps an 8 mm tube run straight through the body while a 1/8" PT male thread branches off at 90 degrees. Push the soft nylon or polyurethane tube into each port until it bottoms out: the stainless spring gasket and POM chuck grip it against pressure, and pressing the release ring lets it drop out again. Unlike the PEB branch tee, whose thread sits in line with one tube leg, the PED forms a true T, so both tube legs stay collinear.
This part belongs to AirTAC's resin and brass one-touch profile: 0 to 1.0 MPa working pressure (0-10 kgf/cm2), 1.5 MPa proof pressure, vacuum down to -750 mmHg (10 Torr) and -20 to +70 C. The body is PBT on a brass stud, the male thread arrives with sealant pre-applied, and the internal seal is an NBR O-ring. Grey is standard; add a D suffix to the code for the black-body version.
Airtac PED T-Shaped Side Thread Tee Fitting PED801 Technical Specifications
| Model | Airtac PED T-Shaped Side Thread Tee Fitting PED801 |
|---|---|
| Type | Male run tee |
| Series | PED |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PED T-Shaped Side Thread Tee Fitting PED801
| PED | Male run tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PED T-Shaped Side Thread Tee Fitting PED801 Is Used
Twin-cylinder feed on a tray sealing machine
Mounted on the 1/8" port of a machine manifold, the PED801 splits one supply into two Dia 8 legs running straight out to the pair of cylinders that clamp trays during sealing.
Vacuum line drop on a sheet lifter
Rated to -750 mmHg, the tee taps a Dia 8 vacuum run mid-line and branches a gauge or sensor off the 1/8" thread without breaking the straight run to the suction cups.
Air knife take-off on a bottling conveyor
Where a bottling conveyor's air knife feed continues downstream, the run tee branches a Dia 8 drop to a reject pusher cylinder while the main line passes straight through.
Is the Airtac PED T-Shaped Side Thread Tee Fitting PED801 the Right Part?
On the 1/8" thread ladder for PED tees you can step down to PED601 (Dia 6) or up to PED1001 (Dia 10). Moving down trims the bore for short runs to small actuators and solenoid valves; moving up to Dia 10 lowers resistance on longer feeds where the same 1/8" port must supply more volume. If the port itself is 1/4", order PED802 instead - same Dia 8 tube side, larger male thread. Whichever you pick, tube OD must match the code exactly: a Dia 8 chuck will not seal on 1/4" (6.35 mm) tube, even though the sizes look close.
Choose a run tee over a branch tee when the two tube legs should form one straight line, and over a bulkhead union (PM) when the split happens in open air rather than through a panel wall.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PED T-Shaped Side Thread Tee Fitting PED801 FAQ
Working pressure 0 to 1.0 MPa (0-10 kgf/cm2), proof pressure 1.5 MPa, vacuum to -750 mmHg (10 Torr), temperature -20 to +70 C. The tube side accepts Dia 8 mm soft nylon or polyurethane tubing and the male thread is 1/8" PT, supplied with sealant on the thread.
Shape and flow path. On the PEB the male thread continues in line with one tube leg, making an L. On the PED801 the two Dia 8 tube ports sit 180 degrees apart in a straight run with the 1/8" thread branching at the middle, so it suits a T-junction where the main line should not turn. If you need the elbow layout, order the PEB equivalent instead.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PED T-Shaped Side Thread Tee Fitting PED801
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.