Airtac PED T-Shaped Side Thread Tee Fitting PED801-S
SUS304 stainless variant (-S)The AirTAC Airtac PED T-Shaped Side Thread Tee Fitting PED801-S is a genuine male run tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale run tee
- SeriesPED
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PED T-Shaped Side Thread Tee Fitting PED801-S
The PED801-S is an AirTAC male run tee from the resin one-touch fitting range. It continues a Dia 8 mm tube run straight through the body and offers a 90 degree branch with a 1/8 in male PT thread, so one push-in part turns a single air line into a supply and a branch without extra couplings.
To make the joint, push the Dia 8 tube fully home; the internal chuck grips the tube wall and the stainless spring gasket and NBR O-ring hold the seal. Press the release ring and the tube frees again. The -S suffix means the male stud is SUS304 stainless steel, while the body stays PBT like the standard PED. Ratings are the resin-line set: 0-1.0 MPa working pressure, 1.5 MPa proof pressure, -750 mmHg vacuum, -20 to +70 C, on soft nylon or polyurethane tubing. Threads arrive with sealant already applied.
Airtac PED T-Shaped Side Thread Tee Fitting PED801-S Technical Specifications
| Model | Airtac PED T-Shaped Side Thread Tee Fitting PED801-S |
|---|---|
| Type | Male run tee |
| Series | PED |
| Connection | Push-in one-touch |
| Body material | Stainless steel 304 (-S variant) |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. Stainless (-S): SUS304 in place of brass - a solid SUS304 body on the PC and POC straight connectors, and a PBT body with a SUS304 stud on the elbow, tee and branch shapes. Working pressure, proof pressure and temperature are unchanged from the standard version. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PED T-Shaped Side Thread Tee Fitting PED801-S
| PED | Male run tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
| -S | Stainless-steel body. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PED T-Shaped Side Thread Tee Fitting PED801-S Is Used
Gauge and sensor pick-off on a screen printer
Tee a 1/8 in PT pressure switch or gauge into the Dia 8 squeegee-air drop of a screen-printing machine while the main run continues to the print head.
Branch circuit on a bottling line conveyor
Split the Dia 8 main supply to feed gripper cylinders downstream, keeping the run tee's straight-through bore so upstream flow is barely disturbed.
Air-assist split on a PCB depaneling router
Run the Dia 8 supply through the tee and take the stainless-stud branch to a blow-off nozzle, where the SUS304 stud suits the electronics workshop's copper-free preference.
Is the Airtac PED T-Shaped Side Thread Tee Fitting PED801-S the Right Part?
Sized both ways on the PED ladder at 1/8 in thread: the step down is PED601-S (Dia 6) for lighter pick-off lines, the step up is PED1001-S (Dia 10) where the branch feeds a larger actuator or a longer run. On the same Dia 8 tube, PED802-S moves the stud to 1/4 in if your port is a bigger tapping. The tube must match Dia 8 exactly - a fitting bored for 8 mm will not seal on 5/16 in imperial tube even though the sizes are close.
Choose a run tee rather than a branch tee (PEB) when the main flow should keep travelling straight past the branch with minimal disturbance, and rather than a bulkhead part (PM/PLM) when no panel wall is involved. If you need the branch angled instead of square, the PYB union Y is the alternative shape.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PED T-Shaped Side Thread Tee Fitting PED801-S FAQ
It is a one-touch male run tee for Dia 8 mm soft nylon or polyurethane tube with a 1/8 in male PT thread. Working pressure is 0-1.0 MPa (0-10 kgf/cm2), vacuum to -750 mmHg (10 Torr), proof pressure 1.5 MPa, and temperature range -20 to +70 C. The -S suffix makes the male stud SUS304 stainless steel; the body remains PBT with a POM release button, stainless spring gasket and NBR O-ring. Ratings are identical to the standard grey PED801.
No. On the PED family the -S option upgrades the male stud to SUS304; the tee body stays PBT, exactly as on the standard part, so the dimensions and push-in action are unchanged. If you need a fully stainless body, that construction exists on the PC and POC straight connectors, not on this tee.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PED T-Shaped Side Thread Tee Fitting PED801-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.