Airtac PED T-Shaped Side Thread Tee Fitting PED802
The AirTAC Airtac PED T-Shaped Side Thread Tee Fitting PED802 is a genuine male run tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale run tee
- SeriesPED
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PED T-Shaped Side Thread Tee Fitting PED802
The AirTAC PED802 is a one-touch male run tee, the threaded version of the PED family. It joins Dia 8 mm soft nylon or polyurethane tube to a 1/4in PT male port, and unlike a branch tee the run continues straight through the body, so the main line passes uninterrupted while a third outlet branches off at 90 degrees.
This is a resin and brass one-touch fitting, rated 0-1.0 MPa (0-10 kgf/cm2) working pressure with -750 mmHg (10 Torr) vacuum capability, 1.5 MPa proof pressure and a -20 to +70 C temperature window. To make a joint, push the tube firmly into the chuck until it bottoms out - the stainless spring gasket and POM chuck grip it, while the NBR O-ring seals. Press the POM release button with the guide ring to free the tube. The brass stud arrives with sealant already applied to the thread; on M5 sizes in this family a sealing gasket is used instead. The body is PBT and the thread is PT throughout this catalogue.
Airtac PED T-Shaped Side Thread Tee Fitting PED802 Technical Specifications
| Model | Airtac PED T-Shaped Side Thread Tee Fitting PED802 |
|---|---|
| Type | Male run tee |
| Series | PED |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PED T-Shaped Side Thread Tee Fitting PED802
| PED | Male run tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PED T-Shaped Side Thread Tee Fitting PED802 Is Used
Solenoid valve manifold supply
Screw the 1/4in stud into a valve manifold inlet and let the Dia 8 run continue to the next drop, branching a dedicated line off to a local actuator without breaking the main circuit.
Packaging machine vacuum ejector feed
On a carton-sealing conveyor, tee a Dia 8 branch off the main supply line to feed a venturi vacuum generator that actuates the hold-down cups, while the run keeps serving the gripper cylinders downstream.
Air drop to workbench regulator
On a machining cell air drop, pass the Dia 8 run straight along the frame and branch through the PED802 to a filter-regulator at the operator bench, keeping the main line uninterrupted for other stations.
Is the Airtac PED T-Shaped Side Thread Tee Fitting PED802 the Right Part?
Dia 8 is the middle of the PED 1/4in ladder, which runs 4, 6, 8, 10 and 12 mm on this thread, so both neighbours exist. Step down to PED602 if the branch feeds a small cylinder or a compact valve where the line volume matters less, or up to PED1002 when the run carries the full supply for several downstream drops. The 1/8in port version, PED801, tops out at Dia 10 tube - worth knowing if you standardise on 12 mm elsewhere. Remember the rule that keeps these joints leak-free: tube OD must match the fitting exactly, so a Dia 8 run tee will not grip 1/4in hose no matter how close it looks.
If your port faces sideways in a tight space, a PH universal elbow swivels to any angle instead. If the main run needs to pass through a panel wall with a union on both sides, the PM bulkhead union is the right shape, not this tee.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PED T-Shaped Side Thread Tee Fitting PED802 FAQ
Working pressure 0-1.0 MPa (0-10 kgf/cm2), usable under vacuum to -750 mmHg (10 Torr), proof pressure 1.5 MPa, and a temperature range of -20 to +70 C. This SKU joins Dia 8 mm tube to a 1/4in PT male thread. It belongs to the resin and brass one-touch profile; tube should be soft nylon or polyurethane.
In the PED run tee the male thread sits on the through-line, so the threaded port is in the same axis as one tube path and the main flow passes straight past the branch. In the PEB branch tee the male thread sits on the perpendicular leg instead. Choose PED when the port belongs on the main run, PEB when the port is the branch point.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PED T-Shaped Side Thread Tee Fitting PED802
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.