Airtac PED T-Shaped Side Thread Tee Fitting PED803
The AirTAC Airtac PED T-Shaped Side Thread Tee Fitting PED803 is a genuine male run tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale run tee
- SeriesPED
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PED T-Shaped Side Thread Tee Fitting PED803
The PED803 is an AirTAC male run tee from the resin-body one-touch range. Its Dia 8 mm tube ports sit on a straight run with the 3/8 in PT male thread in line between them, so the fitting drops into an existing 8 mm air line without bending the run out of path.
Connection is genuinely one-touch: push the soft nylon or polyurethane tube home and the internal chuck grips it against the stainless spring gasket; press the release ring and the tube slides free. The spec profile here is the resin line, not the metal one: 0-1.0 MPa working pressure, -750 mmHg vacuum, 1.5 MPa proof pressure, -20 to +70 C. The body is PBT on a brass stud, and the 3/8 in thread arrives with sealant already applied, so no extra tape is needed on the port.
Airtac PED T-Shaped Side Thread Tee Fitting PED803 Technical Specifications
| Model | Airtac PED T-Shaped Side Thread Tee Fitting PED803 |
|---|---|
| Type | Male run tee |
| Series | PED |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PED T-Shaped Side Thread Tee Fitting PED803
| PED | Male run tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PED T-Shaped Side Thread Tee Fitting PED803 Is Used
Solvent booth valve tapping
Insert a gauge or solenoid tap into a Dia 8 feed line at a paint spray booth, with the 3/8 in PT thread landing straight onto the valve port without an extra nipple.
CNC tool-change air drop
Split a Dia 8 main run on a machining centre so one leg continues to the spindle clamp and the 3/8 in branch feeds the tool-changer circuit.
Trailer brake-line take-off
Tap a commercial vehicle or trailer air preparation line mid-run, keeping the Dia 8 supply uninterrupted while the in-line PT port supplies an auxiliary circuit.
Is the Airtac PED T-Shaped Side Thread Tee Fitting PED803 the Right Part?
Both tube neighbours exist on the PED 3/8 in row: step down to PED603 for a Dia 6 line feeding lighter actuators, or up to PED1003 for a Dia 10 run with more bore behind it. On the thread side, PED802 (1/4 in PT) and PED804 (1/2 in PT) are both made for Dia 8 tube, so match the port you actually have. A Dia 8 fitting will not grip 5/16 in or any other nominal tube - the OD must be exactly 8 mm.
Choose this run-tee shape when a branch must be tapped in-line without altering the run. If the tap has to pass through a panel or enclosure wall instead, PMF is the bulkhead version; if the branch needs to turn at a cylinder port, PL is the elbow answer.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PED T-Shaped Side Thread Tee Fitting PED803 FAQ
Working pressure 0-1.0 MPa (0-10 kgf/cm2), vacuum down to -750 mmHg (10 Torr), proof pressure 1.5 MPa, temperature -20 to +70 C. It takes Dia 8 mm soft nylon or polyurethane tube on both tube ports and has a 3/8 in PT male thread in the run.
No. AirTAC ships the threaded PED803 with sealant already coated on the 3/8 in PT thread, so it screws straight into the port. Only M5 sizes in this range use a sealing gasket instead.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PED T-Shaped Side Thread Tee Fitting PED803
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.