Airtac PL L Connector PL802D
The AirTAC Airtac PL L Connector PL802D is a genuine male elbow for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale elbow
- SeriesPL
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PL L Connector PL802D
The PL802D is an AirTAC PL male elbow from the resin one-touch fitting line, joining Dia 8 mm soft nylon or polyurethane tubing to a 1/4in PT male parallel thread. The 90 degree body turns the tube run sideways from the port, so the tube leaves parallel to the mounting face instead of straight out of it. Push the tube into the chuck until it stops and the grip holds it under pressure; press the POM release ring and the tube slides free again, no tools in either direction.
This is the standard resin pressure profile, not the metal line: 0 to 1.0 MPa working pressure, -750 mmHg vacuum, 1.5 MPa proof pressure and a -20 to +70 C temperature window. The D suffix gives the elbow a black body, and on the PL series that colour change covers the whole housing, not just the button as it does on PC and POC. Inside, a stainless spring gasket and NBR O-ring do the sealing, while the brass stud arrives with thread sealant already applied, so it goes straight onto a tapped PT port.
Airtac PL L Connector PL802D Technical Specifications
| Model | Airtac PL L Connector PL802D |
|---|---|
| Type | Male elbow |
| Series | PL |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PL L Connector PL802D
| PL | Male elbow. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PL L Connector PL802D Is Used
Cylinder ports inside machine guards
On a compact pneumatic cylinder mounted behind a fixed guard, a straight stud leaves no clearance for the hose. The 90 degree PL802D turns an 8 mm tube along the cylinder body, keeping the run inside the guard envelope.
Vacuum ejector lines on pick-and-place heads
At -750 mmHg the resin profile holds vacuum on a packaging-line ejector circuit. The elbow lets the 8 mm vacuum tube route flat along the gantry arm instead of fouling the cable chain above it.
Valve manifold outlets in control cabinets
Where a valve manifold sits close to a cabinet wall, the 1/4in stud threads straight into the outlet port and the elbow points the 8 mm tube along the backplate, clearing the door swing and wire ducts.
Is the Airtac PL L Connector PL802D the Right Part?
On the 1/4in thread this elbow sits mid-ladder: PL602 drops to a Dia 6 tube for lighter actuator lines, PL1002 steps up to Dia 10 when the run feeds a larger bore cylinder and you want less pressure drop along the hose. On the thread side, PL801 keeps the same 8 mm tube on a 1/8in port and PL803 moves it to 3/8in; all three exist in the PL ladder. Match the stud to the port thread and the chuck to the tube OD exactly - a Dia 8 chuck will not seal reliably on 5/16in or 1/4in tube, even if it looks close.
Choose this shape when the port faces into a wall, a guard or another component and a straight PC connector would force an impossible bend into the tubing. If the fitting must pass through a panel and be secured from behind, that is a job for the PMF bulkhead connector instead; PL stays on the outside of the machine.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PL L Connector PL802D FAQ
Working pressure 0 to 1.0 MPa (0 to 10 kgf/cm2), proof pressure 1.5 MPa, negative pressure down to -750 mmHg (10 Torr), and an operating temperature range of -20 to +70 C. The fitting joins Dia 8 mm soft nylon or polyurethane tube to a 1/4in PT male thread, with a black PBT elbow body, POM release button and chuck, stainless spring gasket and NBR O-ring.
No. AirTAC ships the 1/4in threaded stud with sealant already applied, so it is ready to screw into a tapped PT port as delivered. Just confirm the port is genuinely 1/4in PT and the mating seat is clean - then thread it in hand-tight and seat it. Remember the tube side has no such tolerance: the chuck is sized for exactly 8 mm OD tubing.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PL L Connector PL802D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.