Airtac PLL L-Type Extended Thread Connector PLL1002-S
SUS304 stainless variant (-S)The AirTAC Airtac PLL L-Type Extended Thread Connector PLL1002-S is a genuine extended male elbow for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeExtended male elbow
- SeriesPLL
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PLL L-Type Extended Thread Connector PLL1002-S
The PLL1002-S is AirTAC's extended male elbow from the PLL one-touch family, joining Dia 10 mm soft nylon or polyurethane tube to a 1/4in PT male port at a right angle. The extended body gives a longer threaded stud than the standard PL elbow, so it seats deeper into the port and leaves more grip for wrench tightening. The -S suffix means the stud is SUS304 stainless steel; the body itself remains PBT with a POM release button, aluminium-alloy guide, stainless spring gasket and NBR O-ring.
Installation is a hand operation: push the tube fully home and the internal chuck grips it under the stainless spring gasket; press the release ring to free it again. This resin-series part runs at 0-1.0 MPa working pressure, 1.5 MPa proof pressure, holds -750 mmHg vacuum, and is rated -20 to +70 C. The male thread arrives with sealant applied, so no extra tape is needed for the first make-up.
Airtac PLL L-Type Extended Thread Connector PLL1002-S Technical Specifications
| Model | Airtac PLL L-Type Extended Thread Connector PLL1002-S |
|---|---|
| Type | Extended male elbow |
| Series | PLL |
| Connection | Push-in one-touch |
| Body material | Stainless steel 304 (-S variant) |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. Stainless (-S): SUS304 in place of brass - a solid SUS304 body on the PC and POC straight connectors, and a PBT body with a SUS304 stud on the elbow, tee and branch shapes. Working pressure, proof pressure and temperature are unchanged from the standard version. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PLL L-Type Extended Thread Connector PLL1002-S
| PLL | Extended male elbow. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
| -S | Stainless-steel body. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PLL L-Type Extended Thread Connector PLL1002-S Is Used
Wash-down sensor lines
On food and packaging machinery that is hosed down daily, the SUS304 stud on the PLL1002-S resists thread corrosion where a plated brass stud would pit, while the Dia 10 bore feeds gauge and sensor take-offs off a 1/4in manifold port.
Marine deck actuation
Salt-laden air attacks brass studs on hatch and wiper actuators; this elbow's stainless stud with a right-angle body keeps the Dia 10 nylon line flat against the cylinder face on boat deck gear.
Plating line drop legs
Acid fume in electroplating shops corrodes exposed brass threads; an extended-stud elbow turning the Dia 10 supply line down into a rinse-air cylinder port keeps the joint accessible above the tank rim.
Is the Airtac PLL L-Type Extended Thread Connector PLL1002-S the Right Part?
On the 1/4in rung of the PLL ladder, Dia 10 sits between Dia 8 (PLL802) below and Dia 12 (PLL1202) above. Stepping down to Dia 8 buys compactness on a lighter air line; stepping up to Dia 12 lowers resistance on longer runs feeding multi-cylinder circuits. The Dia 10 tube is also offered on this prefix with 1/8in, 3/8in and 1/2in threads, so match the stud to the port rather than changing the tube. Remember that the tube OD must match exactly - a Dia 10 one-touch chuck will not seal 3/8in (10 mm nominal imperial) tube.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PLL L-Type Extended Thread Connector PLL1002-S FAQ
This is the SUS304-stud version of the AirTAC extended male elbow for Dia 10 mm tube on a 1/4in PT male thread. Working pressure 0-1.0 MPa (0-10 kgf/cm2), proof pressure 1.5 MPa, negative pressure -750 mmHg (10 Torr), temperature -20 to +70 C. Suitable tubing is soft nylon or polyurethane. The ratings are identical to the standard PLL1002 - the -S changes only the stud material.
No. On elbow, tee and branch prefixes like PLL, the -S makes the threaded stud SUS304 while the body stays PBT. Only the straight PC and POC connectors get a solid SUS304 body. Do not order this part expecting an all-metal fitting - and if you need full stainless, look at the PC or POC -S straight connectors instead.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PLL L-Type Extended Thread Connector PLL1002-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.