Airtac PLL L-Type Extended Thread Connector PLL1002D-S
SUS304 stainless variant (-S)The AirTAC Airtac PLL L-Type Extended Thread Connector PLL1002D-S is a genuine extended male elbow for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeExtended male elbow
- SeriesPLL
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PLL L-Type Extended Thread Connector PLL1002D-S
The AirTAC PLL1002D-S is an extended male elbow in the resin one-touch range: it joins Dia 10 mm soft nylon or polyurethane tube to a 1/4 in PT male thread, with the tube exiting at 90 degrees from a nose longer than the standard PL elbow, leaving wrench room on crowded manifolds. Push the tube home and the stainless spring gasket and chuck grip it; press the release ring and it frees again. AirTAC applies sealant to the PT thread before packing, so the joint is ready to make up straight from the bag.
Because this SKU ends in -S, AirTAC upgrades the male stud to SUS304 stainless steel while the elbow body stays PBT, now finished in black via the D suffix. The ratings are exactly those of the standard resin line: 0 to 1.0 MPa working pressure, 1.5 MPa proof, -20 to +70 C, and vacuum to -750 mmHg (10 Torr). The stainless stud is the buyer's reason to choose this part where the port face sees corrosive splash or frequent hose-down; note that AirTAC publishes no food or medical certification for the series, so specify it on corrosion grounds only.
Airtac PLL L-Type Extended Thread Connector PLL1002D-S Technical Specifications
| Model | Airtac PLL L-Type Extended Thread Connector PLL1002D-S |
|---|---|
| Type | Extended male elbow |
| Series | PLL |
| Connection | Push-in one-touch |
| Body material | Stainless steel 304 (-S variant) |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. Stainless (-S): SUS304 in place of brass - a solid SUS304 body on the PC and POC straight connectors, and a PBT body with a SUS304 stud on the elbow, tee and branch shapes. Working pressure, proof pressure and temperature are unchanged from the standard version. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PLL L-Type Extended Thread Connector PLL1002D-S
| PLL | Extended male elbow. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
| -S | Stainless-steel body. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PLL L-Type Extended Thread Connector PLL1002D-S Is Used
Plating line rinse stations
On electroplating jigs and rinse-tank frames, splashed acids and salts rapidly pit a plated brass stud at the port. The SUS304 stud on this elbow resists that attack while the PBT body shrugs off the same mist.
Robot gripper air lines
On a six-axis pick-and-place arm, a cylinder port tucked behind the wrist casting needs a 90-degree exit with a longer nose. The extended PLL elbow clears the casting, keeps spanner access, and the Dia 10 bore feeds a medium-size gripper cylinder.
CNC coolant-splash zone
Around a machining-center work enclosure, water-based coolant splashes every fitting near the spindle. Fitting this elbow on the fixture clamping circuit keeps the wetted stud stainless and turns the Dia 10 feed down and away from the spray.
Is the Airtac PLL L-Type Extended Thread Connector PLL1002D-S the Right Part?
Step down to the PLL802 for Dia 8 tube or up to the PLL1202 for Dia 12; both share the same 1/4 in thread, and what changes is the bore and the carrying capacity of the line, not the fitting's footprint. Staying on Dia 10 tube, you can instead move along the thread rung: the PLL1001 drops to 1/8 in PT and the PLL1003 rises to 3/8 in, so match the port you actually have. In every case the tube OD must match exactly - a Dia 10 one-touch chuck will not grip 3/8 in imperial hose.
Pick the PLL shape over a straight PC connector whenever the tube must turn 90 degrees immediately at the port, and over the plain PL elbow when a short body would leave too little thread engagement or no room to swing a spanner behind a guard.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PLL L-Type Extended Thread Connector PLL1002D-S FAQ
It is an extended male elbow one-touch fitting for Dia 10 mm tube with a 1/4 in PT male thread. Working pressure is 0 to 1.0 MPa (0 to 10 kgf/cm2), vacuum to -750 mmHg (10 Torr), proof pressure 1.5 MPa, and working temperature -20 to +70 C on soft nylon or polyurethane tubing. The male stud is SUS304 and the body is PBT in black.
No. On the PLL family AirTAC fits a SUS304 male stud and keeps the elbow body in PBT; only the PC and POC straight connectors get a solid stainless body. The pressure, vacuum and temperature ratings are identical to the standard grey part and the dimensions do not change, so the -S drops in wherever a standard PLL1002D fits.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PLL L-Type Extended Thread Connector PLL1002D-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.