Airtac POC Round Thread Straight Connector POC1001-S
SUS304 stainless variant (-S)The AirTAC Airtac POC Round Thread Straight Connector POC1001-S is a genuine male connector (compact) for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale connector (compact)
- SeriesPOC
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac POC Round Thread Straight Connector POC1001-S
The POC1001-S is an AirTAC POC one-touch male connector in the stainless variant: a straight fitting that joins Dia 10mm soft nylon or polyurethane tubing to a 1/8in PT male port, with the shorter body of the compact POC family. Push the tube in and a stainless spring gasket and chuck grip it; press the release ring and it slides straight back out.
The -S suffix changes the material, not the ratings: on POC connectors the body itself is made from stainless steel 304, and AirTAC states that all parts of the assembly are copper-free. The release button and chuck remain POM, the guide is aluminium alloy, the spring gasket is stainless and the O-ring is NBR. Pressure, vacuum and temperature figures are identical to the standard brass-bodied version, so this part stays within 0-1.0 MPa working pressure and -20 to +70C.
Airtac POC Round Thread Straight Connector POC1001-S Technical Specifications
| Model | Airtac POC Round Thread Straight Connector POC1001-S |
|---|---|
| Type | Male connector (compact) |
| Series | POC |
| Connection | Push-in one-touch |
| Body material | Stainless steel 304 (-S variant) |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. Stainless (-S): SUS304 in place of brass - a solid SUS304 body on the PC and POC straight connectors, and a PBT body with a SUS304 stud on the elbow, tee and branch shapes. Working pressure, proof pressure and temperature are unchanged from the standard version. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac POC Round Thread Straight Connector POC1001-S
| POC | Male connector (compact). |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
| -S | Stainless-steel body. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac POC Round Thread Straight Connector POC1001-S Is Used
Plating line jig cylinders
Copper-free construction makes the POC1001-S a sound choice on jigs and rinse fixtures in electroplating shops, where dissolved copper from a brass fitting can contaminate the bath chemistry.
Beverage bottle-washer sprayers
A stainless 304 body shrugs off the caustic wash-down and rinse cycles around bottle-washing and filling equipment, and the compact POC body fits the crowded valve banks these machines use.
Marine galley air controls
Salt-laden air quickly pits brass studs and nuts. On a boat or dockside compressor loop, this stainless connector on the Dia 10mm run to a galley or hatch actuator keeps the joint serviceable for years.
Is the Airtac POC Round Thread Straight Connector POC1001-S the Right Part?
This SKU sits near the top of the POC 1/8in ladder. Step down one tube size to the POC801 (Dia 8mm, same 1/8in thread) for smaller actuator lines; the next step up in bore at this thread does not exist - POC in 1/8in stops at Dia 10. To feed Dia 12mm tube from the same port you must move to the 1/4in thread, which is the POC1202. Whichever you pick, the tube OD must match the fitting exactly: a Dia 10 connector will not seal on 12mm or on 3/8in tube.
Match the 1/8in PT thread to the port before checking anything else. The thread arrives with sealant already applied, so no extra tape is normally needed, and the male stud seats into any tapped 1/8in PT port on a valve, manifold or cylinder head. If your port is 1/4in, order the -02 thread code rather than adapting with a bushing.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac POC Round Thread Straight Connector POC1001-S FAQ
Working pressure is 0-1.0 MPa (0-10 kgf/cm2), it holds vacuum to -750 mmHg (10 Torr), proof pressure is 1.5 MPa, and the temperature range is -20 to +70C. This SKU is the Dia 10mm tube size with a 1/8in PT male thread, in the SUS304 stainless variant.
AirTAC only makes the POC connector in 1/8in thread for Dia 4, 6, 8 and 10mm tube. If your circuit runs Dia 12mm tubing, order the 1/4in-thread part instead, the POC1202, rather than forcing a mismatched tube into this fitting - the chuck is sized for exactly Dia 10mm.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac POC Round Thread Straight Connector POC1001-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.