The AirTAC Airtac POC Round Thread Straight Connector POC1002D is a genuine male connector (compact) for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
The POC1002D is an AirTAC POC male connector (compact) in the resin one-touch range. It joins Dia 10 mm soft nylon or polyurethane tubing to a 1/4in PT male thread, and the body is noticeably shorter than the standard PC connector, which is exactly why it is chosen when port clearance is tight.
Push the tube straight into the collet chuck until it bottoms and the stainless spring gasket grips it for a pressure-tight seal; press the POM release ring to free the tube again. This resin line is rated 0-1.0 MPa working pressure, resists vacuum down to -750 mmHg (10 Torr), holds 1.5 MPa proof pressure and runs from -20 to 70 C. The male thread arrives with sealant already applied, the stud is brass, and on the POC series the D suffix changes only the release button to black - the body stays standard grey.
| Model | Airtac POC Round Thread Straight Connector POC1002D |
|---|---|
| Type | Male connector (compact) |
| Series | POC |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
| POC | Male connector (compact). |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Short-index pick-and-place cells use small-bore grippers tucked between tooling plates; the compact POC body clears the adjacent clamp bracket where a full-length PC connector would foul, and Dia 10 tubing feeds the gripper's short, high-cycle strokes.
A 5/2 solenoid manifold on a bottle-capper station presents a 1/4in PT outlet; screwing the pre-sealed POC1002D stud into the port gives an immediate push-in take-off for Dia 10 polyurethane line running to the capping cylinder.
Divertor-gate cylinders on carton conveyor systems often sit behind tight guarding; the compact connector threads directly into the 1/4in cylinder port and the Dia 10 PU line exits straight through the guard slot without an extra elbow.
On the 1/4in thread ladder the POC spans Dia 4 through Dia 12, so the direct neighbours of this part are POC802 (Dia 8) below and POC1202 (Dia 12) above. Stepping down trims the bore and the air demand the line can carry; stepping up suits actuators fed from longer runs. If you change thread instead, note the quirk of the POC ladder: 1/8in supports only up to Dia 10, so POC1001 exists, while the 3/8in row starts at Dia 8, so POC1003 exists too.
The tubing OD must match this fitting exactly - a Dia 10 chuck will not seal on 3/8in or 12 mm tube. If you need a solid stainless body rather than this PBT-body, brass-stud part, that is the -S variant territory, and it carries the identical pressure figures.
Quick checklist
It is an AirTAC POC compact male connector for Dia 10 mm tubing with a 1/4in PT male thread. Working pressure is 0-1.0 MPa (0-10 kgf/cm2), vacuum capability is -750 mmHg (10 Torr), proof pressure is 1.5 MPa and the operating temperature range is -20 to 70 C. It suits soft nylon or polyurethane tube, and this D version carries the black release button.
No. AirTAC supplies POC threaded studs with sealant pre-applied on the PT thread, so you can screw it straight into a 1/4in port. Remember the tube side is size-critical: only genuine Dia 10 mm OD soft nylon or polyurethane tube will lock into the chuck, and reusing scored or oval tube ends risks a leak even when the fitting itself is sound.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard parts are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.