Airtac PYB Y-Type Threaded Tee Fitting PYB602
The AirTAC Airtac PYB Y-Type Threaded Tee Fitting PYB602 is a genuine branch y for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeBranch Y
- SeriesPYB
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PYB Y-Type Threaded Tee Fitting PYB602
The AirTAC PYB602 is a PYB branch Y one-touch fitting: a single 1/4in PT male thread feeding two Dia 6 mm tube ports set at a Y angle. It is the shape to reach for when one valve outlet has to serve two lines without a separate tee and extra hex joints.
Push each soft nylon or PU tube into its port and the internal chuck grips it for a pressure-tight hold; press the release ring to free it. This is the resin/brass profile: 0-1.0 MPa working pressure, -750 mmHg vacuum, 1.5 MPa proof pressure and -20 to +70 C. The PBT threaded body carries factory-applied sealant on the 1/4in thread, and the POM release button and NBR O-ring do the sealing at the tube.
Airtac PYB Y-Type Threaded Tee Fitting PYB602 Technical Specifications
| Model | Airtac PYB Y-Type Threaded Tee Fitting PYB602 |
|---|---|
| Type | Branch Y |
| Series | PYB |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PYB Y-Type Threaded Tee Fitting PYB602
| PYB | Branch Y. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PYB Y-Type Threaded Tee Fitting PYB602 Is Used
Packaging machine twin grippers
One 1/4in valve outlet on a carton-closing machine splits through the PYB602 into two Dia 6 lines feeding a pair of small gripper cylinders that fire together.
Lab automation air distribution
On a benchtop pipette or plate-handling module, the Y divides a single regulated supply into two Dia 6 branches serving an actuator and a small air jet.
Conveyor line blow-off pair
A 1/4in port on the manifold of a bottling conveyor feeds the PYB602, branching Dia 6 tube to two angled nozzles that clear caps or label debris.
Is the Airtac PYB Y-Type Threaded Tee Fitting PYB602 the Right Part?
On the PYB ladder this Dia 6 version sits between PYB402 (Dia 4 tubes, 1/4in thread) and PYB802 (Dia 8 tubes, 1/4in thread). Stepping down to Dia 4 suits light pilot lines and small actuators; stepping up to Dia 8 drops restriction on runs feeding bigger cylinders. Both tube ports on any one PYB are the same size, so the whole Y changes with the code, not just one leg.
Match the 1/4in PT thread to the port before anything else - a spare manifold outlet tapped 1/4in takes this fitting directly. Remember the tube rule: tube OD must match exactly, so 1/4in (6.35 mm) imperial tube will not seat in a Dia 6 port.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PYB Y-Type Threaded Tee Fitting PYB602 FAQ
It is a PYB branch Y one-touch fitting with two Dia 6 mm tube ports and a 1/4in PT male thread. Working pressure 0-1.0 MPa (0-10 kgf/cm2), negative pressure -750 mmHg (10 Torr), proof pressure 1.5 MPa, operating temperature -20 to +70 C. Use soft nylon or polyurethane tubing. Body is PBT with a brass stud; release button and chuck are POM, the O-ring is NBR. The thread arrives with sealant applied.
No. Both tube ports on a PYB602 are Dia 6 mm; the Y is symmetrical, and there is no mixed-size version in the branch Y range. If your two lines run different tube ODs, take Dia 6 out of this fitting and step one leg down at the actuator with a PG reducer such as PG6-4, which keeps each connection a proper push-in joint.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PYB Y-Type Threaded Tee Fitting PYB602
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.