Airtac PYB Y-Type Threaded Tee Fitting PYB602D
The AirTAC Airtac PYB Y-Type Threaded Tee Fitting PYB602D is a genuine branch y for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeBranch Y
- SeriesPYB
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PYB Y-Type Threaded Tee Fitting PYB602D
The PYB602D is an AirTAC PYB branch Y one-touch fitting in the black D-colour version. It takes a single 1/4in PT male thread and splits it into two diverging Dia 6mm tube ports, so one threaded port on a valve or manifold can feed two tube runs. Push each tube home and the stainless spring gasket plus POM chuck grip it; press the release ring and the tube frees again.
This sits in the resin and brass one-touch family: 0 to 1.0 MPa working pressure, -750 mmHg vacuum, 1.5 MPa proof pressure and -20 to +70 C. The 1/4in male thread arrives with sealant already applied, and on the PYB series the D suffix changes the whole body to black, not just the button as on PC connectors - useful if you colour-code air circuits on the machine.
Airtac PYB Y-Type Threaded Tee Fitting PYB602D Technical Specifications
| Model | Airtac PYB Y-Type Threaded Tee Fitting PYB602D |
|---|---|
| Type | Branch Y |
| Series | PYB |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PYB Y-Type Threaded Tee Fitting PYB602D
| PYB | Branch Y. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PYB Y-Type Threaded Tee Fitting PYB602D Is Used
Twin vacuum cups on a pick-and-place gantry
One 1/4in port on the vacuum manifold branches to two Dia 6 lines, one per cup, with the Y angle keeping the runs short and the tubing swept clear of the gantry rails.
Dual-acting slide on a packaging line
Feed both sides of a double-acting gripper slide from a single valve outlet, saving a tee block and a threaded port on a crowded valve plate.
Two cooling air jets from one control panel port
A Dia 6 branch off the panel supply feeds a pair of blow-off nozzles over a printing or labelling head, with the black body blending into dark enclosures.
Is the Airtac PYB Y-Type Threaded Tee Fitting PYB602D the Right Part?
On the 1/4in PYB row you can step down to PYB402 (Dia 4) for lighter pick-and-place lines or up to PYB802 (Dia 8) when the branch feeds two larger actuators; bigger bores raise flow headroom but each step needs the matching tube. On Dia 6 the thread ladder runs 1/8in (PYB601), 1/4in (this part) and 3/8in (PYB603), so match the port you are screwing into rather than upsizing on hope. Remember the tube OD must match exactly - a Dia 6 port will not hold 1/4in imperial tube.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PYB Y-Type Threaded Tee Fitting PYB602D FAQ
Working pressure 0 to 1.0 MPa (0 to 10 kgf/cm2), negative pressure down to -750 mmHg (10 Torr), proof pressure 1.5 MPa and temperature range -20 to +70 C. It joins Dia 6mm soft nylon or polyurethane tube to a 1/4in PT male thread, black body with POM chuck and release button, brass stud and NBR O-ring.
No. Both tube ports on this branch Y are Dia 6mm - the two legs always match. If you need to split a supply into two different diameters, use the AirTAC PYW different-diameter union Y instead, which is made specifically for mixed tube sizes.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PYB Y-Type Threaded Tee Fitting PYB602D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.