Airtac SAIF Series Standard Cylinder with Valve SAIF100X200S-10B
The AirTAC Airtac SAIF Series Standard Cylinder with Valve SAIF100X200S-10B is a genuine double-acting ISO 15552 cylinder with a Ø100mm bore, 200mm stroke and a built-in 4M310-10 5/2 solenoid valve — it switches itself from one coil signal, so no separate remote valve or extra plumbing is needed.
- BoreØ100 mm
- Stroke200 mm
- Built-in valve4M310-10
- Valve port3/8"
- CoilDC24V
- EntryTerminal
About the Airtac SAIF Series Standard Cylinder with Valve SAIF100X200S-10B
The AirTAC SAIF100X200S-10B is a double-acting ISO 15552 profile cylinder equipped with a built-in 4M310-10 5/2 solenoid valve. Delivering a Cv of 1.68 and a robust 3927 Newtons of push force at 0.5 MPa, it integrates pneumatic motion and directional control into a single decentralized unit. This specific configuration features a PT3/8 cylinder port, a PT3/8 valve port, and a carbon steel piston rod. Because the valve operates at 0.15-0.8 MPa, this defines the practical working pressure range for the assembled SAIF unit, even though the bare cylinder rates to 1.0 MPa.
Wired for DC24V with a terminal electrical entry, the coil consumes 3.0 W, features IP65 protection, and activates in 0.05 seconds or less. By default, the factory setting retracts the piston rod when the coil is energised, but this behavior can be reconfigured to extend-when-energised simply by repositioning the valve. The integrated manifold uses PU tubing (O10 x O6.5) to bridge the valve and cylinder, eliminating the need for separate remote valves and drastically reducing panel space and plumbing across large machines. The -S magnet option enables position sensing with AirTAC CMSE reed or DMSE electronic solid-state switches.
Airtac SAIF Series Standard Cylinder with Valve SAIF100X200S-10B Technical Specifications
| Model | Airtac SAIF Series Standard Cylinder with Valve SAIF100X200S-10B |
|---|---|
| Series | SAIF ISO 15552 cylinder with valve |
| Bore size | Ø100 mm |
| Stroke | 200 mm |
| Acting type | Double acting, self-valved |
| Cylinder port | G1/2 |
| Rod thread | M20×1.5 |
| PU tube | Ø10 × Ø6.5 |
| Built-in valve | 4M310-10 (5/2) |
|---|---|
| Valve flow | 30.0 mm² (Cv 1.68) |
| Max frequency | 4 cycle/sec |
| Coil voltage | DC24V · DC 3.0 W |
| Electrical entry | Terminal · IP65 · B class |
| Response time | 0.05 s and below |
| Operating pressure | 0.15 – 0.8 MPa (valve limit) |
| Speed range | 30 – 800 mm/s |
The cylinder rates to 1.0 MPa but the built-in valve operates 0.15–0.8 MPa, so run the assembled SAIF at 0.15–0.8 MPa. Default: rod retracts when the coil is energised (reconfigurable to extend). Specs follow the official AirTAC SAIF datasheet. Port options: PT / G.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
Sized within the valve's 0.15–0.8 MPa range. Actual usable force is lower than theoretical due to friction and back-pressure.
Model Code: Airtac SAIF Series Standard Cylinder with Valve SAIF100X200S-10B
| SAIF | ISO 15552 cylinder with built-in 4M valve. |
|---|---|
| 100×200 | Bore × stroke in mm. |
| -10 | Valve port 3/8" → 4M310-10. |
| B | Coil voltage DC24V. |
| I / (blank) | Terminal electrical entry. |
SAIF does not hold its load without air — the valve routes air, it is not a lock. For load-holding use a SAIL (lock) or BSAI (clamp-lock).
Where the Airtac SAIF Series Standard Cylinder with Valve SAIF100X200S-10B Is Used
Decentralized Automation Stations
Eliminates long air lines from a central panel by integrating the 4M310 valve directly on the cylinder, saving wiring and plumbing space across large-scale factory layouts.
High-Force Clamping Jigs
Delivers 3927N of push force at 0.5 MPa for heavy-duty machining clamps, using the built-in 5/2 valve to switch itself from a single DC24V signal.
Space-Constrained Machine Retrofits
Ideal for upgrading older equipment where running new valve tubing is costly, providing a complete self-switching actuator with CMSE/DMSE sensor tracking.
Is the Airtac SAIF Series Standard Cylinder with Valve SAIF100X200S-10B the Right Choice?
Choose this 100mm bore SAIF when an application demands high thrust (3927N push at 0.5 MPa) alongside self-contained directional control. If a machine layout requires fewer remote valve islands and less tubing, this decentralized configuration is ideal. Compared to stepping down to an 80mm bore (which provides 2513N push at 0.5 MPa), the 100mm bore is necessary for heavier loads. The 4M310 valve offers a 30.0 mm2 effective area and a max frequency of 4 cycles per second. For stroke lengths of 200mm, side-loading is minimal, but any stroke exceeding 300mm requires external guide support to prevent rod wear.
When replacing this unit, verify the 100mm bore, 200mm stroke, PT3/8 valve port, DC24V terminal coil, PT tapered threads, and the -S magnet. Remember that the 5/2 valve routes air and holds position via internal pilot pressure; it is not a mechanical lock. If true load-holding is required during air loss, consider the SAIL (lock) or BSAI (clamp-lock) series instead.
Quick checklist
- ✓ Force at 0.15–0.8 MPa
- ✓ Coil voltage matches panel
- ✓ Terminal vs grommet entry
- ✓ Retract- or extend-when-energised
- ✓ Load-holding → SAIL / BSAI
Airtac SAIF Series Standard Cylinder with Valve SAIF100X200S-10B FAQ
The built-in 4M310-10 valve has an effective area of 30.0 mm2 (Cv 1.68). The 100mm bore cylinder generates 3927 Newtons of push force and 3681 Newtons of pull force at 0.5 MPa.
No, the 5/2 solenoid valve routes air and holds its last position via internal pilot pressure, but it is not a mechanical lock. The factory setting retracts the rod when energised, which can be reconfigured to extend-when-energised by repositioning the valve. For true load-holding, use the SAIL or BSAI series.
Related AirTAC Cylinders & Valves
Request a Quote for Airtac SAIF Series Standard Cylinder with Valve SAIF100X200S-10B
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.