The AirTAC Airtac TR Twin-Rod Cylinders TR10X100S is a genuine TR twin-rod (double-rod) double-acting cylinder, 10 mm bore. Two parallel rods on one plate resist bending and twisting and let the load mount without rotating. It delivers about 78.6 N of push at 0.5 MPa. A front bumper cushions the impact and adjusts the stroke over a -5 to 0 mm range. As the JIS guide-grade series it adds high non-rotating precision, a lengthening sliding guide (no added lubricant) and two-side ports.
The TR10X100S is a double-acting twin-rod cylinder: two parallel rods ride on one shared plate, so the load mounts directly without rotating and the plate resists bending and twisting. At bore 10 with a 100 mm stroke, it delivers about 78.5 N of push thrust at 0.5 MPa (pull side is lower) - enough for pushing, clamping and light transfer jobs over a longer travel. A bumper at the front cushions impact and also adjusts the stroke over -5 to 0 mm.
This is a genuine AirTAC part built to the JIS standard TR specification - the precise guide grade of twin-rod cylinder, with high non-rotating accuracy, low rod-end deflection, and a lengthening sliding-support guide that needs no added lubricant. Two groups of ports sit on both sides for flexible piping, and the magnet is fitted as standard with magnetic-switch slots around the body. Dimensions and sizing are confirmed from the datasheet on request.
| Model | Airtac TR Twin-Rod Cylinders TR10X100S |
|---|---|
| Type | Twin-rod cylinder, double acting |
| Series / standard | TR (JIS standard) |
| Bore | 10 mm |
| Push thrust @0.5 MPa | 78.6 N |
| Port size | M5x0.8 (PT, G or NPT thread) |
| Fluid | Air, filtered to 40 um |
|---|---|
| Operating pressure | 0.2 - 1.0 MPa (29 - 145 psi) |
| Proof pressure | 1.5 MPa (215 psi) |
| Temperature | -20 to 70 C |
| Speed range | 30 - 500 mm/s |
| Cushion | Bumper, stroke adjustable -5 to 0 mm |
| Magnet | Standard (magnetic-switch slots around the body) |
Specifications follow the official AirTAC TN/TR twin-rod data. Operating pressure is set by bore (0.2 MPa minimum on the 6 and 10 mm bores). The front cover and piston are short, so avoid an over-long stroke. Overall dimensions vary per stroke and allowable side-load is published as curves — ask us and we confirm from the datasheet.
Bore 10 runs at 0.2-1.0 MPa (29-145 psi) with about 78.5 N push thrust at 0.5 MPa (pull side lower). If your load needs more force, step up to the next bore in the TR range (16/20/25/32) rather than over-pressurising. Within the TR series you can also choose the enterprise-standard TN instead if you do not need TR's precise guide, though TN covers a slightly different bore set. Strokes follow the bore's stroke table; take care with over-long strokes on a small bore, and route any side-load question to us for the datasheet curves. Ports on this bore are M5x0.8. TR is offered with PT, G or NPT threads - this model is PT.
Mounted beside a conveyor, the plate pushes cartons or trays sideways into sorting lanes over the 100 mm travel, staying square to the belt because the twin rods stop the push plate from rotating.
Fitted to a machining or assembly jig, it clamps a workpiece against a stop; the anti-rotation plate keeps the clamp pad flat on the part through every cycle.
Used under a light platform or chute gate, it raises and lowers small components between levels; the twin-rod guide resists twisting so the platform travels level.
TR is the JIS-standard twin-rod series (the precise guide grade), 10 is the bore in mm, 100 is the stroke in mm, and S confirms the magnet, which is fitted as standard on every TR model. With no trailing thread letter, the ports are PT; TR is also available with G or NPT threads.
Yes - the two rods on a shared plate are the point of the design: the load mounts without rotating and the plate resists bending and twisting. The allowable side-load and deflection are published only as datasheet curves, and overall dimensions vary with stroke, so confirm both from the datasheet before finalising your fixture.