The AirTAC Airtac TR Twin-Rod Cylinders TR10X60S is a genuine TR twin-rod (double-rod) double-acting cylinder, 10 mm bore. Two parallel rods on one plate resist bending and twisting and let the load mount without rotating. It delivers about 78.6 N of push at 0.5 MPa. A front bumper cushions the impact and adjusts the stroke over a -5 to 0 mm range. As the JIS guide-grade series it adds high non-rotating precision, a lengthening sliding guide (no added lubricant) and two-side ports.
The TR10X60S is a double-acting twin-rod cylinder: two parallel pistons and rods drive one shared mounting plate, which resists bending and twisting and accepts the load without rotating. The 10 mm bore with a 60 mm stroke gives about 78.5 N of push thrust at 0.5 MPa across the two pistons, suited to longer-travel push and transfer moves on light parts. A front bumper cushions the stroke end and adjusts the effective stroke over -5 to 0 mm.
This is a genuine AirTAC part built to the JIS-standard TR series, the precise guide grade: high non-rotating accuracy, low rod-end deflection, and a lengthening sliding-support guide that needs no added lubrication. The magnet is standard on every model, with switch slots around the body for magnetic sensors. Overall dimensions are per stroke, so we confirm sizing from the datasheet on request.
| Model | Airtac TR Twin-Rod Cylinders TR10X60S |
|---|---|
| Type | Twin-rod cylinder, double acting |
| Series / standard | TR (JIS standard) |
| Bore | 10 mm |
| Push thrust @0.5 MPa | 78.6 N |
| Port size | M5x0.8 (PT, G or NPT thread) |
| Fluid | Air, filtered to 40 um |
|---|---|
| Operating pressure | 0.2 - 1.0 MPa (29 - 145 psi) |
| Proof pressure | 1.5 MPa (215 psi) |
| Temperature | -20 to 70 C |
| Speed range | 30 - 500 mm/s |
| Cushion | Bumper, stroke adjustable -5 to 0 mm |
| Magnet | Standard (magnetic-switch slots around the body) |
Specifications follow the official AirTAC TN/TR twin-rod data. Operating pressure is set by bore (0.2 MPa minimum on the 6 and 10 mm bores). The front cover and piston are short, so avoid an over-long stroke. Overall dimensions vary per stroke and allowable side-load is published as curves — ask us and we confirm from the datasheet.
Match the bore to your thrust: the 10 mm bore delivers about 78.5 N push at 0.5 MPa over an operating range of 0.2-1.0 MPa (29-145 psi); 16 to 32 mm bores are available when you need more force and run at 0.15-1.0 MPa. TR is the JIS series with the precise sliding-support guide, while TN is the enterprise alternative with PT thread only - the TR series offers PT, G and NPT, and this model is PT. The 60 mm stroke sits within the bore's standard stroke table; be cautious about stretching to very long strokes on short covers, and send side-load questions to us because allowable side load is published as curves only.
Over a 60 mm travel, the twin-rod plate pushes small totes or blister packs off a conveyor at a right angle without the push face twisting off-line.
The non-rotating plate raises a part into a pick position and presents it the same way every time, ready for a robot or nest.
Used as a fine positioning slide, the precise guide holds the plate aligned while the adjustable bumper sets the end position within -5 to 0 mm.
Both are double-acting twin-rod cylinders. TR is the JIS-standard series with the precise guide grade - higher non-rotating accuracy, low rod-end deflection, a lengthening sliding-support guide needing no added lubrication, and two groups of ports on both sides. TN is the enterprise series, PT thread only. Choose TR when alignment accuracy matters; both are magnet-fitted as standard.
The two parallel rods give the plate good resistance to rotation and twisting, and the load mounts directly on the plate. However, allowable side load and rod-end deflection are published only as curves, not single numbers - send us your load and offset details and we will confirm suitability from the datasheet.