Airtac BSE Clamp Standard Cylinder BSE50X75S
The AirTAC Airtac BSE Clamp Standard Cylinder BSE50X75S is a genuine double-acting ISO 15552 cylinder with an integrated spring-applied, air-released ROD LOCK. If air is cut or an E-stop is hit, the collet clamps the Ø20mm rod and holds up to 1400 N in either direction — no drift. Ø50mm bore, 75mm stroke, PT1/4 cylinder ports, G1/8 lock-release port.
- BoreØ50 mm
- Stroke75 mm
- Static holding force1400 N
- Lock typeSpring-lock / air-release
- Cylinder portPT1/4
- Lock-release portG1/8
About the Airtac BSE Clamp Standard Cylinder BSE50X75S
The AirTAC BSE50X75S is a double-acting ISO 15552 profile cylinder with an integrated spring-applied, air-released rod lock. It delivers a 1400 N bidirectional static holding force, securing your load in both directions without consuming live air.
Operating pressure is capped at 0.7 MPa. The drive function runs on a PT1/4 port, while a separate G1/8 release port unlocks the collet mechanism. This 50 mm bore includes a -S magnet for CMSE or DMSE electronic sensors and provides adjustable air cushions at both ends.
Rod Lock — 1400 N Static Holding (Ø50mm)
A spring clamps the collet onto the rod, so the Airtac BSE Clamp Standard Cylinder BSE50X75S holds its position in both directions when air is lost, exhausted or an E-stop trips. Apply 0.15–0.7 MPa to the G1/8 release port to unlock. Engage the lock only after the rod has stopped (it is not a dynamic brake), and release only when the pressures on both sides of the piston are balanced. Allow at least 0.5 s for full release before moving.
Airtac BSE Clamp Standard Cylinder BSE50X75S Technical Specifications
| Model | Airtac BSE Clamp Standard Cylinder BSE50X75S |
|---|---|
| Series | BSE ISO 15552 rod-lock cylinder |
| Bore size | Ø50 mm |
| Stroke | 75 mm |
| Static holding force | 1400 N |
| Cylinder port | PT1/4 |
| Lock-release port | G1/8 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Unlocking pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC BSE datasheet. The lock uses the SE standard body; SE mounting accessories fit BSE except FTC. Port options: PT (standard) / G (BSPP); lock-release port is G1/8.
Theoretical Output Force (Ø50mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa (max) | 1374 N | — |
| Max drive (@0.7 MPa) | 140 kgf | |
Drive force is separate from the 1400 N static holding force of the lock. BSE operates up to 0.7 MPa. Size with a safety margin.
Model Code: Airtac BSE Clamp Standard Cylinder BSE50X75S
| B | Rod-lock cylinder prefix. |
|---|---|
| SE | ISO 15552 standard double-acting body. |
| 50 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Thread: PT (blank) / G. Mounting (BSE): Basic, LB, FA, FB, CA, CB, CR, TC (FTC is not available on BSE). Related: SE (no lock), BSED (double-rod rod lock). Sensors CMSE/DMSE fit magnetic BSE.
Where the Airtac BSE Clamp Standard Cylinder BSE50X75S Is Used
Vertical Pneumatic Lift
Holds a 982 N vertical lift assembly mid-stroke. The 1400 N fail-safe collet locks instantly if air exhausts, preventing a 50 mm bore load from dropping.
Tooling Clamp
Secures a machining fixture during an E-stop. The spring-applied lock maintains the 1400 N grip without live air, while the 825 N pull retracts the tool.
Pallet Stop Gate
Blocks pallets on a conveyor line. The rod lock holds the 50 mm stop pin rigidly against impact, releasing only when 0.15-0.7 MPa air is supplied to the G1/8 port.
Is the Airtac BSE Clamp Standard Cylinder BSE50X75S the Right Cylinder?
Verify your suspended load stays below the 1400 N holding capacity. If you need less drive force, step down to the 40 mm bore (628 N push @0.5 MPa, 900 N hold). For heavier loads, step up to the 63 mm bore (1559 N push @0.5 MPa, 2200 N hold). Always engage the lock only after the rod fully stops, and release it only when piston pressures are balanced, allowing at least 0.5 s before moving.
This 75 mm stroke avoids the side-load risks of longer strokes. To replace this unit, match the 50 mm bore, 75 mm stroke, PT1/4 porting, and -S magnet. Standard SE mounting accessories fit this body, except the FTC bracket.
Quick checklist
- ✓ Load to hold ≤ 1400 N?
- ✓ Fail-safe hold on air loss / E-stop needed
- ✓ Lock engaged only when stopped
- ✓ G1/8 release-air line available
- ✓ Magnet (-S) for CMSE/DMSE sensors?
Installation & Safety Notes
- check Engage the lock only after the rod has stopped — not as a dynamic brake.
- check Release only when both piston sides are pressure-balanced.
- check Allow ≥0.5 s for full release before commanding motion.
- check Feed the G1/8 release port with 0.15–0.7 MPa clean air.
- check Add safety-rated controls for man-rated / overhead loads.
- check Use SE mounting accessories (FTC excepted).
Airtac BSE Clamp Standard Cylinder BSE50X75S FAQ
The spring-applied collet provides a 1400 N static holding force in both directions if air is lost. The drive forces are 982 N push and 825 N pull at 0.5 MPa, 1374 N push at 0.7 MPa, with a maximum drive of 140 kgf.
You must balance the air pressure on both sides of the piston first. Then supply 0.15-0.7 MPa to the separate G1/8 release port, and wait at least 0.5 seconds before commanding cylinder movement to ensure the collet fully retracts.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC BSE Cylinders
Request a Quote for Airtac BSE Clamp Standard Cylinder BSE50X75S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.