Airtac PB Pen-type Cylinder PB10X10CBY
The AirTAC Airtac PB Pen-type Cylinder PB10X10CBY is a double-acting pen-size (mini) air cylinder with a Ø10mm bore and 10mm stroke. Its slim round barrel and back cover are stainless steel, the M5×0.8 ports keep plumbing compact, and the fast, low-friction piston suits high-cycle small-part handling.
- BoreØ10 mm
- Stroke10 mm
- Port sizeM5×0.8
- Acting typeDouble acting
- Rod threadM8×1.0
- CushionElastic bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PB Pen-type Cylinder PB10X10CBY
The AirTAC PB10X10CBY is a double-acting JIS pen-size mini cylinder engineered for compact, high-frequency small-part motion. It features a slim SUS304 stainless steel round barrel and piston rod, offering excellent durability in damp or mildly corrosive environments while saving valuable space and payload on light end-of-arm tooling. Generating 39.3 N of push force at 0.5 MPa, this unit is equipped with a CB double clevis for pivoting applications.
Air enters via an M5x0.8 port, driving the 4 mm rod at speeds of 50-800 mm/s. End-of-stroke energy is managed by a fixed TPU bumper at each end rather than an adjustable air cushion, meaning it only decelerates the final few millimeters. For higher cycling speeds with real tooling mass, metering out the exhaust or adding an external shock absorber is recommended to prevent the bumper from bottoming out.
Airtac PB Pen-type Cylinder PB10X10CBY Technical Specifications
| Model | Airtac PB Pen-type Cylinder PB10X10CBY |
|---|---|
| Series | PB JIS pen-size mini cylinder |
| Bore size | Ø10 mm |
| Rod diameter | Ø4 mm |
| Stroke | 10 mm |
| Acting type | Double acting |
| Port size | M5×0.8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.2 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 50 – 800 mm/s |
| Cushion | Elastic bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC PB pen-size datasheet. Piston rod and barrel are stainless steel. Confirm bore, stroke and back-cover option against the product label before installation.
Theoretical Output Force (Ø10mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 39.3 N | 33.0 N |
| 0.7 MPa (max) | 55.0 N | 46.2 N |
Values are taken from the AirTAC PB thrust table. Because pull acts on the rod-side annular area, pull force is always lower than push. Actual usable force is reduced by friction — size with a margin.
Model Code: Airtac PB Pen-type Cylinder PB10X10CBY
| PB | JIS pen-size double-acting mini-cylinder series. |
|---|---|
| 10 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| CB / U / R | Back cover: CB double clevis, U 90° side inlet, R axial inlet (bore-dependent). |
Mounting accessories: LB, FA, CJ. Related PB-family variants: PSB (single-acting push), PTB (single-acting pull), PBD (double rod), PBJ (adjustable stroke), PBR (front-mount).
Where the Airtac PB Pen-type Cylinder PB10X10CBY Is Used
PCB Pick-and-Place
Cycles a vacuum gripper on a surface mount machine, using the short 10 mm stroke and CB clevis to pivot tiny electronic components into precise board locations.
Pouch Sealing Flap
Tucks and presses cardboard flaps on a compact packaging line, where the 39.3 N extend force easily secures light carton tabs without crushing the product.
Lab Sample Diverting
Actuates a small pivot gate on an automated analyzer to route test tubes, benefiting from the SUS304 build to resist humidity and chemical splashes.
Is the Airtac PB Pen-type Cylinder PB10X10CBY the Right Cylinder?
If you need to step down, the Ø6 bore provides 14.2 N of push at 0.5 MPa; stepping up to the Ø12 bore yields 56.5 N. Keep in mind the 4 mm rod is built for coaxial thrust, so over long strokes or off-axis loads you should add an external linear bearing to prevent side-load damage. A plain PB body does not hold its load if air pressure is lost or the valve is centered, so an external rod lock is required for fail-safe positioning.
To order this exact configuration, confirm the 10 mm bore, 10 mm stroke, M5x0.8 port, CB double clevis back cover, and no sensor magnet. The maximum standard stroke available for this bore is 200 mm.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Slim pen body vs. a standard round cylinder
- ✓ Back cover: CB / U / R inlet direction
- ✓ Magnet (S) for sensors?
- ✓ Mounting: LB / FA / CJ or front thread
- ✓ Keep the load coaxial — avoid side load
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 0.7 MPa operating pressure.
- check Keep the load coaxial; avoid side load on the thin rod.
- check Do not dismantle the front or back cover.
- check Fit dust caps to ports during long-term storage.
- check Installation by qualified personnel per AirTAC docs.
Airtac PB Pen-type Cylinder PB10X10CBY FAQ
At 0.5 MPa, the push force is 39.3 N and the pull force is 33 N. At the maximum operating pressure of 0.7 MPa, the push force is 55 N and the pull force is 46.2 N. The operating pressure range is 0.15-0.7 MPa, with a proof pressure of 1.2 MPa. It operates at speeds between 50 and 800 mm/s.
The CB back cover is a double clevis designed specifically for pivoting mounts, allowing the cylinder to articulate smoothly as the load moves. At the stroke ends, a fixed TPU bumper decelerates the piston over the last few millimeters. This bumper is not adjustable and does not lock the position, so for heavy pivoting masses at high speeds, an external shock absorber is advised.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC PB Pen-Size Cylinders
Request a Quote for Airtac PB Pen-type Cylinder PB10X10CBY
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.