Airtac PB Pen-type Cylinder PB12X175SR
The AirTAC Airtac PB Pen-type Cylinder PB12X175SR is a double-acting pen-size (mini) air cylinder with a Ø12mm bore and 175mm stroke. Its slim round barrel and back cover are stainless steel, the M5×0.8 ports keep plumbing compact, and the fast, low-friction piston suits high-cycle small-part handling.
- BoreØ12 mm
- Stroke175 mm
- Port sizeM5×0.8
- Acting typeDouble acting
- Rod threadM10×1.0
- CushionElastic bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PB Pen-type Cylinder PB12X175SR
The AirTAC PB12X175SR is a double-acting JIS pen-size mini cylinder engineered for compact, high-frequency small-part motion. It generates 56.5 N of push and 46.7 N of pull at 0.5 MPa, utilizing a slim SUS304 stainless steel barrel and piston rod to resist damp or mildly corrosive environments. The R axial inlet keeps plumbing perfectly in-line with the body, saving valuable space on tight jigs.
Equipped with a built-in S magnet, this unit interfaces directly with AirTAC reed or electronic switches for precise position detection. Operating at speeds from 50-800 mm/s, it relies on a fixed TPU bumper at each end to decelerate the piston. Because the 175 mm stroke is substantial for a Ø12 bore, the slender Ø5 mm rod requires an external guide or linear bearing if subjected to any off-axis loads, as the rod is designed purely for coaxial thrust.
Airtac PB Pen-type Cylinder PB12X175SR Technical Specifications
| Model | Airtac PB Pen-type Cylinder PB12X175SR |
|---|---|
| Series | PB JIS pen-size mini cylinder |
| Bore size | Ø12 mm |
| Rod diameter | Ø5 mm |
| Stroke | 175 mm |
| Acting type | Double acting |
| Port size | M5×0.8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.2 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 50 – 800 mm/s |
| Cushion | Elastic bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC PB pen-size datasheet. Piston rod and barrel are stainless steel. Confirm bore, stroke and back-cover option against the product label before installation.
Theoretical Output Force (Ø12mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 56.5 N | 46.7 N |
| 0.7 MPa (max) | 79.1 N | 65.4 N |
Values are taken from the AirTAC PB thrust table. Because pull acts on the rod-side annular area, pull force is always lower than push. Actual usable force is reduced by friction — size with a margin.
Model Code: Airtac PB Pen-type Cylinder PB12X175SR
| PB | JIS pen-size double-acting mini-cylinder series. |
|---|---|
| 12 | Bore size in mm. |
| ×175 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| CB / U / R | Back cover: CB double clevis, U 90° side inlet, R axial inlet (bore-dependent). |
Mounting accessories: LB, FA, CJ. Related PB-family variants: PSB (single-acting push), PTB (single-acting pull), PBD (double rod), PBJ (adjustable stroke), PBR (front-mount).
Where the Airtac PB Pen-type Cylinder PB12X175SR Is Used
PCB Depaneling Router
Actuates a tooling pin on an automated depaneling fixture, where the slim 12 mm body clears adjacent conveyor rails and the S magnet confirms pin retraction.
Blister Pack Sealing Press
Provides 56.5 N of extend force to clamp thin film layers against a heated platen, with the R axial inlet keeping hoses safely out of the moving heat zone.
Sorting Diverter Arm
Pushes lightweight plastic caps off a high-speed belt line, utilizing the 175 mm stroke to reach across the lane while the TPU bumper softens the rapid extend stop.
Is the Airtac PB Pen-type Cylinder PB12X175SR the Right Cylinder?
When sizing this model, stepping down to a Ø10 bore yields 39.3 N of push at 0.5 MPa, while stepping up to a Ø16 bore provides 100.5 N, letting you fine-tune force to your exact jig requirements.
Remember that a plain pen-size body does not hold its position if air pressure drops or the valve is centered; the piston will drift, and the fixed bumper only decelerates near stroke end, so an external rod lock is required for fail-safe holding. To finalize your order, confirm the 12 mm bore, 175 mm stroke, M5x0.8 port, S magnet, and R axial inlet configuration.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Slim pen body vs. a standard round cylinder
- ✓ Back cover: CB / U / R inlet direction
- ✓ Magnet (S) for sensors?
- ✓ Mounting: LB / FA / CJ or front thread
- ✓ Keep the load coaxial — avoid side load
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 0.7 MPa operating pressure.
- check Keep the load coaxial; avoid side load on the thin rod.
- check Do not dismantle the front or back cover.
- check Fit dust caps to ports during long-term storage.
- check Installation by qualified personnel per AirTAC docs.
Airtac PB Pen-type Cylinder PB12X175SR FAQ
At 0.5 MPa, the push force is 56.5 N and the pull force is 46.7 N. At the maximum operating pressure of 0.7 MPa, the push is 79.1 N and the pull is 65.4 N. The operating pressure range is 0.15-0.7 MPa, with a proof pressure of 1.2 MPa and an operating speed of 50-800 mm/s.
It uses a fixed TPU bumper at each end that decelerates the piston over the last few millimeters; it is not adjustable, so for high-speed or heavy tooling mass you should meter-out the exhaust or add an external shock absorber. The built-in S magnet allows you to mount AirTAC reed or electronic switches directly to the body for position feedback.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC PB Pen-Size Cylinders
Request a Quote for Airtac PB Pen-type Cylinder PB12X175SR
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.