Airtac PB Pen-type Cylinder PB12X75CB
The AirTAC Airtac PB Pen-type Cylinder PB12X75CB is a double-acting pen-size (mini) air cylinder with a Ø12mm bore and 75mm stroke. Its slim round barrel and back cover are stainless steel, the M5×0.8 ports keep plumbing compact, and the fast, low-friction piston suits high-cycle small-part handling.
- BoreØ12 mm
- Stroke75 mm
- Port sizeM5×0.8
- Acting typeDouble acting
- Rod threadM10×1.0
- CushionElastic bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PB Pen-type Cylinder PB12X75CB
The AirTAC PB12X75CB is a double-acting JIS pen-size mini cylinder engineered for compact, high-frequency small-part motion. It features a slim SUS304 stainless steel barrel and piston rod that shrugs off damp or mildly corrosive industrial environments. Delivering 56.5 N of push and 46.7 N of pull at 0.5 MPa, this 12mm bore unit integrates a CB double clevis back cover for pivoting loads.
Air enters via an M5x0.8 port, driving the 5mm rod at speeds from 50-800 mm/s. End-of-stroke energy is managed by fixed TPU bumpers rather than adjustable cushions, meaning they only decelerate the final few millimeters. For rapid cycling with real tooling mass, metering out the exhaust or adding an external shock absorber is recommended to prevent the bumpers from bottoming out.
Airtac PB Pen-type Cylinder PB12X75CB Technical Specifications
| Model | Airtac PB Pen-type Cylinder PB12X75CB |
|---|---|
| Series | PB JIS pen-size mini cylinder |
| Bore size | Ø12 mm |
| Rod diameter | Ø5 mm |
| Stroke | 75 mm |
| Acting type | Double acting |
| Port size | M5×0.8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.2 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 50 – 800 mm/s |
| Cushion | Elastic bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC PB pen-size datasheet. Piston rod and barrel are stainless steel. Confirm bore, stroke and back-cover option against the product label before installation.
Theoretical Output Force (Ø12mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 56.5 N | 46.7 N |
| 0.7 MPa (max) | 79.1 N | 65.4 N |
Values are taken from the AirTAC PB thrust table. Because pull acts on the rod-side annular area, pull force is always lower than push. Actual usable force is reduced by friction — size with a margin.
Model Code: Airtac PB Pen-type Cylinder PB12X75CB
| PB | JIS pen-size double-acting mini-cylinder series. |
|---|---|
| 12 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| CB / U / R | Back cover: CB double clevis, U 90° side inlet, R axial inlet (bore-dependent). |
Mounting accessories: LB, FA, CJ. Related PB-family variants: PSB (single-acting push), PTB (single-acting pull), PBD (double rod), PBJ (adjustable stroke), PBR (front-mount).
Where the Airtac PB Pen-type Cylinder PB12X75CB Is Used
Pivoting Divert Gate
Swings a lightweight sorting flap on a packaging conveyor using the CB double clevis to accommodate the arc motion without binding the rod.
PCB Probe Actuation
Drives a spring-loaded test probe block into electronic test fixtures, where the slim stainless body resists flux fumes and saves valuable tooling space.
Small Component Ejection
Pushes molded plastic caps out of a multi-cavity mold area, relying on the 56.5 N extend force to cleanly break the parts free without marking them.
Is the Airtac PB Pen-type Cylinder PB12X75CB the Right Cylinder?
When sizing this 12mm bore actuator, stepping down to the Ø10 variant yields 39.3 N of push at 0.5 MPa, while stepping up to the Ø16 provides 100.5 N, allowing you to scale force precisely. Because the 5mm rod is designed strictly for coaxial thrust, avoid side loading and add a linear bearing if guiding off-axis loads over the 75mm stroke. Note that a plain PB body does not hold position if air pressure drops; the piston will drift, so an external rod lock is required for fail-safe holding. Confirm your ordering essentials: 12mm bore, 75mm stroke, CB double clevis, no magnet, M5x0.8 port, and M10x1.0 rod-end thread.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Slim pen body vs. a standard round cylinder
- ✓ Back cover: CB / U / R inlet direction
- ✓ Magnet (S) for sensors?
- ✓ Mounting: LB / FA / CJ or front thread
- ✓ Keep the load coaxial — avoid side load
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 0.7 MPa operating pressure.
- check Keep the load coaxial; avoid side load on the thin rod.
- check Do not dismantle the front or back cover.
- check Fit dust caps to ports during long-term storage.
- check Installation by qualified personnel per AirTAC docs.
Airtac PB Pen-type Cylinder PB12X75CB FAQ
At 0.5 MPa, the push force is 56.5 N and the pull force is 46.7 N. At the maximum operating pressure of 0.7 MPa, the push force is 79.1 N and the pull force is 65.4 N. The operating pressure range is 0.15-0.7 MPa, with a proof pressure of 1.2 MPa. It operates at speeds between 50-800 mm/s in temperatures from -20 to +70 C.
No, the PB12X75CB does not feature a locking mechanism. If air is lost or the valve is centered, the piston will drift. The fixed TPU bumpers only decelerate the rod near the stroke ends; they do not function as a brake. An external stop or rod lock must be installed if your application requires fail-safe position holding.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC PB Pen-Size Cylinders
Request a Quote for Airtac PB Pen-type Cylinder PB12X75CB
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.