Airtac PBJ Adjustable Pen-Type Cylinder PBJ16X90-10S
The AirTAC Airtac PBJ Adjustable Pen-Type Cylinder PBJ16X90-10S is a double-acting, double-rod pen-size mini cylinder whose rear rod carries a stroke adjuster. On a Ø16mm bore it gives a nominal 90mm stroke with a 10mm fine-adjustable window — settable from 80 to 90mm, so you set the end position without changing hardware.
- BoreØ16 mm
- Nominal stroke90 mm
- Adjust window10 mm
- Effective range80–90 mm
- Port sizeM5×0.8
- Acting typeDouble acting
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PBJ Adjustable Pen-Type Cylinder PBJ16X90-10S
The AirTAC PBJ16X90-10S is a double-acting, double-rod pen-size mini cylinder with a 10mm adjustable window. A rear M5x0.8 adjuster screw and lock nut shorten the retract end, giving an effective stroke range of 80-90mm. The extend end remains fixed. The M5x0.8 air port and Ø5mm rod keep the unit compact.
Built with a SUS304 stainless barrel and rod, this slim cylinder saves space in tight jigs. It includes a fixed TPU bumper at each end and a built-in piston magnet for position sensing.
Airtac PBJ Adjustable Pen-Type Cylinder PBJ16X90-10S Technical Specifications
| Model | Airtac PBJ Adjustable Pen-Type Cylinder PBJ16X90-10S |
|---|---|
| Series | PBJ JIS pen-size adjustable-stroke cylinder |
| Bore size | Ø16 mm |
| Rod diameter | Ø5 mm |
| Nominal stroke | 90 mm |
| Adjustable window | 10 mm (80–90 mm) |
| Adjuster thread | M5×0.8 |
| Port size | M5×0.8 |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.2 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 50 – 800 mm/s |
| Cushion | Elastic bumper (both ends) |
| Max standard stroke | Up to 200 mm |
PBJ is a double-rod cylinder: the rear rod carries the stroke adjuster, which sets the stroke end within the adjustable window. Confirm the set position against the product label before installation.
Theoretical Output Force (Ø16mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 90.7 N | 90.7 N |
| 0.7 MPa (max) | 126.9 N | 126.9 N |
The rear rod passes through the rear cover, so both piston faces lose rod area: push is shown at the annular-area value (conservative), lower than a single-rod PB push of the same bore. Size with a friction margin.
Model Code: Airtac PBJ Adjustable Pen-Type Cylinder PBJ16X90-10S
| PBJ | JIS pen-size adjustable-stroke mini-cylinder series. |
|---|---|
| 16 | Bore size in mm. |
| ×90 | Nominal stroke length in mm. |
| -10 | Adjustable-stroke window in mm (10/20/30/40/50/75/100). |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
Fixed body — no separate back-cover code. Mounting accessories: LB, FA. Related PB-family variants: PB (fixed stroke), PBD (double rod), PBR (front-mount).
Where the Airtac PBJ Adjustable Pen-Type Cylinder PBJ16X90-10S Is Used
Variable-Depth Insertion
Dial in the 80-90mm retract stop to set precise insertion depths for pressing pins or plugs without machining new hard stops.
Changeover Fixtures
Quickly retune the back position when switching between product variants on a shared jig, saving hardware swap time.
Trial Stop Positioning
Use the rear M5x0.8 adjuster screw to find the optimal end-of-stroke location during prototype runs before locking the nut.
Is the Airtac PBJ Adjustable Pen-Type Cylinder PBJ16X90-10S the Right Cylinder?
Remember that only the back position is tunable—the extend end is fixed. Always re-tighten the lock nut after setting your 80-90mm range to prevent vibration drift. Confirm your ordering essentials: 16mm bore, 90mm nominal stroke, 10mm window, S magnet, and any LB or FA mount.
The thin Ø5mm rod handles coaxial thrust well, but over long strokes or off-axis loads you should add an external guide or linear bearing to prevent side-load damage. A plain pneumatic body does not hold position on air loss, so install an external stop if fail-safe holding is required.
Quick checklist
- ✓ Need to fine-tune the end position on site
- ✓ Retract end sits within 80–90 mm
- ✓ Force at your working pressure
- ✓ Magnet (S) for sensors?
- ✓ Access to the rear adjuster screw
- ✓ Keep the load coaxial — avoid side load
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 0.7 MPa operating pressure.
- check Set the adjuster, then re-lock the check nut.
- check Double rod: the rear rod carries the stroke adjuster.
- check Keep the load coaxial; avoid side load on the thin rod.
- check Do not dismantle the front or back cover.
Airtac PBJ Adjustable Pen-Type Cylinder PBJ16X90-10S FAQ
The effective stroke range is 80-90mm. Adjusting the stroke does not alter these forces.
A rear screw shortens the retract end only; the extend end is fixed. You must re-tighten the lock nut after setting your desired length to prevent vibration drift. The built-in S magnet works with AirTAC reed or electronic switches for position sensing.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC PBJ Pen-Size Cylinders
Request a Quote for Airtac PBJ Adjustable Pen-Type Cylinder PBJ16X90-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.