Airtac PC Threaded Straight Connector PC804D
The AirTAC Airtac PC Threaded Straight Connector PC804D is a genuine male connector for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale connector
- SeriesPC
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PC Threaded Straight Connector PC804D
The PC804D is an AirTAC PC male connector, the straight threaded one-touch fitting that joins a Dia 8 mm soft nylon or polyurethane tube to a 1/2 inch PT male port. Push the tube in and the stainless spring gasket and chuck grip it against the POM seal; press the release button and the tube slides straight back out. The grey POM button on this SKU is delivered in the D black version - on the PC series the D suffix changes only the release button, not the brass body, so the fitting you bolt in is the familiar grey-bodied PC with a black press point for colour-coded circuits.
This is the resin-line spec profile, not the metal BPC line: working pressure 0-1.0 MPa (0-10 kgf/cm2), vacuum down to -750 mmHg (10 Torr), proof pressure 1.5 MPa and a temperature window of -20 to +70 C. The thread seat is brass with a brass stud and arrives with sealant already applied, so no additional tape or dope is needed before it goes into the port.
Airtac PC Threaded Straight Connector PC804D Technical Specifications
| Model | Airtac PC Threaded Straight Connector PC804D |
|---|---|
| Type | Male connector |
| Series | PC |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PC Threaded Straight Connector PC804D
| PC | Male connector. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PC Threaded Straight Connector PC804D Is Used
Valve manifold supply port
A 1/2 inch PT manifold inlet on a solenoid valve island is a natural landing point for this connector - the PC804D drops an 8 mm drop line straight off the supply gallery without an adapter.
Large-bore pneumatic press cylinder
Feeding the 1/2 inch rear port of an 8 mm-line air cylinder on a small pneumatic press or clamping station, where the black release button stands out against the grey body for quick identification at the cell.
Compressor to air-prep drop
Routing an 8 mm nylon line from a receiver tank or compressor outlet down to a filter-regulator-lubricator unit, with the PC804D making the push-in break point for seasonal maintenance.
Is the Airtac PC Threaded Straight Connector PC804D the Right Part?
On the 1/2 inch thread row of the PC ladder the tube options are Dia 6, 8, 10 and 12, so PC804D sits in the middle of that group. Step down to PC604 if the port is being fed by 6 mm lines - the same thread, a narrower bore, lower air demand per stroke. Step up to PC1004 for a 10 mm supply serving longer runs or higher-consumption actuators. PC804D is the right pick when the machine already runs 8 mm tubing and the connection point is a large 1/2 inch port such as a valve manifold inlet or a big cylinder head. There is no larger thread than 1/2 inch on the PC series, so this is the top of the threaded ladder - for a bigger bore you move to a flange or hard-piped solution instead.
Tube OD must match exactly: an 8 mm chuck will not seal 1/4 inch or 5/16 inch tube, even when it looks close. Match the PT male thread to the female port and hand-start it before tightening; the pre-applied sealant does the rest.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PC Threaded Straight Connector PC804D FAQ
The PC804D is a PC series one-touch male connector for Dia 8 mm tube with a 1/2 inch PT male thread. Working pressure is 0-1.0 MPa (0-10 kgf/cm2), it holds vacuum to -750 mmHg (10 Torr), proof pressure is 1.5 MPa and the operating temperature range is -20 to +70 C. It suits soft nylon or polyurethane tubing. The body seat and stud are brass, the button and chuck are POM, and the D suffix here means a black release button; on PC parts the D changes the button only. The thread arrives with sealant applied.
No. The internal chuck and gasket are sized to the exact tube OD, so the PC804D accepts 8 mm tube only and will leak or release with anything else. For 10 mm on the same 1/2 inch thread order PC1004; for 6 mm on that thread order PC604. Mixing imperial tube into a metric one-touch fitting is the most common cause of blow-off at pressure, so measure the tube outside diameter before ordering.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PC Threaded Straight Connector PC804D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.