Airtac PCF Female Thread Straight Fitting PCF1001D
The AirTAC Airtac PCF Female Thread Straight Fitting PCF1001D is a genuine female connector for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeFemale connector
- SeriesPCF
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PCF Female Thread Straight Fitting PCF1001D
The PCF1001D is an AirTAC PCF one-touch female connector: the fitting that screws onto a male 1/8in PT stud and converts it into a push-in socket for Dia 10mm soft nylon or polyurethane tubing. Push the tube home and the internal chuck grips it against the stainless spring gasket; press the release ring and the tube slides straight back out. No tools, no ferrules, no re-tightening.
This is the resin/brass one-touch profile, not the metal BP line: 0-1.0 MPa (0-10 kgf/cm2) working pressure, -750 mmHg (10 Torr) vacuum, 1.5 MPa proof pressure and -20 to +70C. Construction is a POM release button and chuck, aluminium-alloy guide, stainless spring gasket and NBR O-ring on a PBT body. The D suffix makes the body black on this series, unlike PC and POC where D recolours only the release button. The female thread arrives with sealant pre-applied.
Airtac PCF Female Thread Straight Fitting PCF1001D Technical Specifications
| Model | Airtac PCF Female Thread Straight Fitting PCF1001D |
|---|---|
| Type | Female connector |
| Series | PCF |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PCF Female Thread Straight Fitting PCF1001D
| PCF | Female connector. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PCF Female Thread Straight Fitting PCF1001D Is Used
Valve island drop lines
On a bottling-line filler, each solenoid outlet presents a 1/8in male stud. A PCF1001D screwed onto each stud hands off to Dia 10 polyurethane runs feeding the larger gripper and clamp cylinders downstream.
Pick-and-place ejector feed
A SCARA pick-and-place wrist needs a short, light vacuum line. The 1/8in female thread suits the compact ejector stud, and the circuit holds -750 mmHg (10 Torr) for suction-cup work without a separate vacuum-rated fitting.
Screen-printing machine clamps
Screen-printing clamp cylinders with male 1/8in studs take the PCF1001D directly, running Dia 10 soft nylon to the fixture clamps. Keep it away from flash-cure zones, since the resin profile tops out at 70C.
Is the Airtac PCF Female Thread Straight Fitting PCF1001D the Right Part?
Tube OD must match exactly: this body holds 10mm tube only, never 3/8in imperial or 12mm. One step down on the same 1/8in thread sits Dia 8 tube, the usual choice for lighter single-actuator lines; one step up is Dia 12, which on female-connector ladders generally wants a 1/4in thread or larger, so a 12mm circuit usually moves you up the thread ladder as well. If your port is a 1/4in female thread instead, keep Dia 10 tube and switch to the 02 thread code.
Pick a female connector when the machine already presents a male stud - valve-island outlets and cylinder port studs are the classic cases. Where the tube must turn 90 degrees tight to the port, use a PLF female elbow; where the fitting must pass through a cabinet wall and be secured by a locknut behind it, the PMF bulkhead female connector is the correct shape.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PCF Female Thread Straight Fitting PCF1001D FAQ
Working pressure 0-1.0 MPa (0-10 kgf/cm2), negative pressure -750 mmHg (10 Torr), proof pressure 1.5 MPa, temperature -20 to +70C. It accepts Dia 10mm soft nylon or polyurethane tube and has a 1/8in PT female thread. It belongs to the resin/brass one-touch profile with a black PBT body, not the 0.9 MPa / 150C metal BP line.
No. AirTAC ships these threaded one-touch parts with sealant already applied to the thread, so the PCF1001D seals onto a male 1/8in PT stud as delivered. Only the M5 sizes in the range use a sealing gasket instead of thread sealant.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PCF Female Thread Straight Fitting PCF1001D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.