Airtac PCF Female Thread Straight Fitting PCF1002D
The AirTAC Airtac PCF Female Thread Straight Fitting PCF1002D is a genuine female connector for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeFemale connector
- SeriesPCF
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PCF Female Thread Straight Fitting PCF1002D
The PCF1002D is an AirTAC PCF female connector, the one-touch fitting with an internal thread on the opposite side of the tube port. This version takes Dia 10 mm soft nylon or polyurethane tube into the push-in socket and presents a 1/4 in female PT thread for mating directly onto a male stud, so no separate nipple is needed between the fitting and the valve or cylinder port. The D suffix makes the body black rather than the standard grey, which many builders use to colour-code user-serviceable air points on a machine.
As a resin one-touch part it is rated 0-1.0 MPa working pressure, -750 mmHg vacuum, 1.5 MPa proof pressure and -20 to +70 C. Push the tube square into the socket and the internal chuck grips the OD while the stainless spring gasket and NBR O-ring seal it; press the POM release ring to free the tube again. Do not confuse this with AirTAC's metal BPC line, which trades a lower 0.9 MPa rating for a 0 to +150 C temperature range.
Airtac PCF Female Thread Straight Fitting PCF1002D Technical Specifications
| Model | Airtac PCF Female Thread Straight Fitting PCF1002D |
|---|---|
| Type | Female connector |
| Series | PCF |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PCF Female Thread Straight Fitting PCF1002D
| PCF | Female connector. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PCF Female Thread Straight Fitting PCF1002D Is Used
Solenoid valve manifold outlets
Screws straight onto the 1/4 in male outlet of a valve manifold on a packaging machine, turning a Dia 10 mm line toward the downstream cylinder without an extra straight adapter in between.
Pneumatic control panel distribution
The black D body lets panel builders mark Dia 10 mm distribution drops distinctly from grey Dia 6 mm signal lines inside a control cabinet that feeds several machine stations.
Vacuum pick-and-place circuits
Rated to -750 mmHg, so it suits the suction side of a vacuum ejector circuit lifting flat cartons or glass sheets on a handling table using Dia 10 mm soft nylon tube.
Is the Airtac PCF Female Thread Straight Fitting PCF1002D the Right Part?
At Dia 10 you are on the second-largest tube in the PCF ladder. Step down to PCF802 for Dia 8 mm tube feeding smaller actuators, or up to PCF1202 for Dia 12 mm trunk lines where the extra bore matters for long runs. On the thread side, PCF1001 covers the same Dia 10 tube on a 1/8 in female port and PCF1003 steps up to 3/8 in. The fitting cannot stretch across sizes: a Dia 10 socket will not grip 3/8 in (10 mm nominal imperial) tube properly, and the tube OD must match exactly.
Choose the female thread when the equipment side already carries a male stud with its own seal, which saves a joint and a leak path. If you need to turn 90 degrees at the port, move to the PLF female elbow instead; for passing through a sheet-metal panel, the PMF bulkhead connector is the right shape.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PCF Female Thread Straight Fitting PCF1002D FAQ
Working pressure 0-1.0 MPa (0-10 kgf/cm2), vacuum down to -750 mmHg (10 Torr), proof pressure 1.5 MPa, and a temperature range of -20 to +70 C. The fitting joins Dia 10 mm soft nylon or polyurethane tube to a 1/4 in female PT thread, and the D suffix gives it the black body.
No. On the PC and POC straight connectors the D changes only the release button, but on the other series including PCF it changes the body itself to black. Everything else is identical: same brass stud, PBT thread section, POM chuck, stainless spring gasket and NBR O-ring, and the same 0-1.0 MPa rating.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PCF Female Thread Straight Fitting PCF1002D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.