Airtac PCF Female Thread Straight Fitting PCF1202D
The AirTAC Airtac PCF Female Thread Straight Fitting PCF1202D is a genuine female connector for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeFemale connector
- SeriesPCF
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PCF Female Thread Straight Fitting PCF1202D
The PCF1202D is an AirTAC PCF female elbow, a one-touch fitting that turns a Dia 12 mm tube through 90 degrees into a 1/4in female PT thread. Because the thread is internal, the fitting screws straight onto a male stud port or nipple with no extra adaptor between them. To make the joint, push the tube firmly into the chuck until it bottoms out; the stainless spring gasket and chuck jaws grip it against pressure and vibration, and pressing the POM release ring frees it again for rework.
This is the resin and brass one-touch profile, not the metal BP line: working pressure 0-1.0 MPa, vacuum down to -750 mmHg (10 Torr), proof pressure 1.5 MPa and a service range of -20 to +70 C with soft nylon or polyurethane tubing. The 1/4in thread arrives with sealant already applied. The D suffix here denotes the black version, which on the PCF family covers the body, so the fitting can be colour-coded into a machine circuit at a glance.
Airtac PCF Female Thread Straight Fitting PCF1202D Technical Specifications
| Model | Airtac PCF Female Thread Straight Fitting PCF1202D |
|---|---|
| Type | Female connector |
| Series | PCF |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PCF Female Thread Straight Fitting PCF1202D
| PCF | Female connector. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PCF Female Thread Straight Fitting PCF1202D Is Used
Pneumatic clamp cylinder port
Threads directly onto the male port stud of a compact clamp cylinder inside a tight fixture guard, taking the 12 mm supply line off at a right angle so nothing stands proud of the cylinder body.
Packaging machine valve manifold
Screws onto the 1/4in outlet stud of a solenoid valve manifold on a form-fill-seal machine, dropping the tube down to a bag-clamp actuator without an elbow nipple in the stack.
Rotary indexing table drop
On an eight-station rotary dial table, the elbow turns the 12 mm actuator line downward from a port on the index ring, keeping the tubing clear of the rotating fixture plate above.
Is the Airtac PCF Female Thread Straight Fitting PCF1202D the Right Part?
Dia 12 mm is the top of the tube ladder, so the only step down is Dia 10 (PCF1002), which buys you a slimmer profile and lower flow where a line is only feeding a small actuator or sensor block. On the thread side, 1/4in sits between 1/8in (PCF1201) for compact valve ports and 3/8in (PCF1203) for higher-demand drops, so check the port you are threading onto before ordering.
A female elbow is the right answer when the port itself is male-threaded and a straight fitting would stand off the machine wall or foul a guard. Match the tube OD exactly: this chuck holds 12.0 mm tube only and will not seal on 1/2in (12.7 mm) hose, a mismatch that is a common cause of slow leaks on retrofit jobs.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PCF Female Thread Straight Fitting PCF1202D FAQ
It is an AirTAC PCF one-touch female elbow for Dia 12 mm tube with a 1/4in female PT thread. Working pressure is 0-1.0 MPa (0-10 kgf/cm2), it holds vacuum to -750 mmHg (10 Torr), proof pressure is 1.5 MPa and the working temperature range is -20 to +70 C with soft nylon or polyurethane tubing. This is the standard resin and brass profile, and the D suffix makes it the black-bodied version.
No extra preparation is needed: AirTAC ships threaded one-touch parts with sealant already applied to the thread, so the PCF1202D can be wound straight onto the male port. Only M5 sizes in this catalogue use a sealing gasket instead. Hand-tighten to seat the sealant, and remember the internal thread means the mating port must be male-studded for the elbow to sit flush.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PCF Female Thread Straight Fitting PCF1202D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.