Airtac PCF Female Thread Straight Fitting PCF602D
The AirTAC Airtac PCF Female Thread Straight Fitting PCF602D is a genuine female connector for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeFemale connector
- SeriesPCF
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PCF Female Thread Straight Fitting PCF602D
The AirTAC PCF602D is a one-touch female connector: the tubing side is a Dia 6 mm push-in socket, the machine side is a 1/4 in internal PT taper thread that screws onto a male stud or nipple. Push the soft nylon or polyurethane tube straight in and the stainless spring gasket plus POM chuck grip it against the brass-body passageway; press the release ring and the tube comes free again. Because the D suffix sits on a PCF, it recolours the entire body black, not just the release button - unlike PC and POC straights, where black affects only the button.
This is the resin and brass one-touch profile: working pressure 0-1.0 MPa (0-10 kgf/cm2), vacuum down to -750 mmHg, proof pressure 1.5 MPa, and a temperature window of -20 to +70 C. The internal thread arrives pre-sealed from the factory, so it mates onto a taped or pre-coated 1/4 in male taper stud without extra paste. The -750 mmHg rating also means the same part can sit on a vacuum ejector line as well as a pressure line.
Airtac PCF Female Thread Straight Fitting PCF602D Technical Specifications
| Model | Airtac PCF Female Thread Straight Fitting PCF602D |
|---|---|
| Type | Female connector |
| Series | PCF |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PCF Female Thread Straight Fitting PCF602D
| PCF | Female connector. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PCF Female Thread Straight Fitting PCF602D Is Used
Solenoid valve manifold studs
Screws onto the pre-threaded 1/4 in male outlets of a 5/2 solenoid manifold on a packaging machine, turning each station into a 6 mm push-in point for gripper and clamp lines.
Vacuum pick-and-place circuits
The -750 mmHg rating lets the same fitting serve the ejector side of a robotic pick-and-place cell, feeding 6 mm vacuum tube to suction cups on cartons or blister packs.
Machine rebuilds in dark enclosures
The all-black body blends into painted guards and dark control cabinets on retrofitted machine tools, where grey resin fittings stand out against the frame.
Is the Airtac PCF Female Thread Straight Fitting PCF602D the Right Part?
You are in the middle of the PCF 1/4 in ladder, which runs Dia 4, 6, 8, 10 and 12. One step down is PCF402D - a smaller bore feeding lighter loads such as a single small cylinder, with slightly less capacity per metre of run. One step up is PCF802D, whose wider 8 mm bore carries more volume to faster or longer strokes. Tube OD must match exactly: a Dia 6 socket will not seal on 6.35 mm (1/4 in) imperial tube.
If the thread is the variable instead, the same Dia 6 socket is also offered as PCF601 (1/8 in) and PCF603 (3/8 in) - check which male stud your manifold actually presents before ordering. And if your port is female rather than male, a PC male connector, not this PCF, is the part you want.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PCF Female Thread Straight Fitting PCF602D FAQ
It is a one-touch female connector taking Dia 6 mm soft nylon or polyurethane tube on a 1/4 in internal PT taper thread, with a black body. Working pressure is 0-1.0 MPa (0-10 kgf/cm2), vacuum rating -750 mmHg, proof pressure 1.5 MPa, and operating temperature -20 to +70 C.
On the PCF series the D recolours the whole body to black, not merely the release button as on PC and POC straights. Pressures, temperatures and dimensions are identical to the grey version, so you order it purely for appearance or colour-coding by circuit.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PCF Female Thread Straight Fitting PCF602D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.