Airtac PEB T-Shaped Straight Thread Tee Connector PEB1002D-S
SUS304 stainless variant (-S)The AirTAC Airtac PEB T-Shaped Straight Thread Tee Connector PEB1002D-S is a genuine male branch tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale branch tee
- SeriesPEB
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PEB T-Shaped Straight Thread Tee Connector PEB1002D-S
The PEB1002D-S is an AirTAC male branch tee, the -S stainless variant in black. It splits a Dia 10 mm push-in line into two: the run passes straight through and a 1/4in PT male stud branches off at 90 degrees for a hard-plumbed takeoff. Assembly is genuinely one-touch - push the tube past the POM release button into the chuck and the stainless spring gasket grips it under pressure; press the release ring and the tube slides free for rework.
The stainless story on this family is specific: the push-in body stays glass-reinforced PBT with a POM button, aluminium guide and NBR O-ring, while the male stud that threads into a metal port is SUS304. That is exactly where corrosion starts on a wet or wash-down machine, so the upgrade is placed where it earns its keep. The PT thread arrives pre-coated with sealant, so no extra tape is needed at fitting time.
Airtac PEB T-Shaped Straight Thread Tee Connector PEB1002D-S Technical Specifications
| Model | Airtac PEB T-Shaped Straight Thread Tee Connector PEB1002D-S |
|---|---|
| Type | Male branch tee |
| Series | PEB |
| Connection | Push-in one-touch |
| Body material | Stainless steel 304 (-S variant) |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. Stainless (-S): SUS304 in place of brass - a solid SUS304 body on the PC and POC straight connectors, and a PBT body with a SUS304 stud on the elbow, tee and branch shapes. Working pressure, proof pressure and temperature are unchanged from the standard version. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PEB T-Shaped Straight Thread Tee Connector PEB1002D-S
| PEB | Male branch tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
| -S | Stainless-steel body. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PEB T-Shaped Straight Thread Tee Connector PEB1002D-S Is Used
Branch feed to a wash-down rinse valve
The SUS304 stud threads into a stainless valve port on a food rinse station, with the Dia 10 run and 90-degree branch routed in soft nylon tube that shrugs off daily hose-downs.
Splitting a manifold run on a packaging machine
The through-run carries main supply along the machine frame while the 1/4in branch drops a dedicated feed to a vacuum generator or reject-actuator circuit.
Plating-line actuator takeoff
In copper-sensitive plating and electronics processes, the PBT body and stainless stud keep copper alloy hardware away from the line where acid mist attacks exposed brass.
Is the Airtac PEB T-Shaped Straight Thread Tee Connector PEB1002D-S the Right Part?
On the 1/4in thread ladder this tee sits between the PEB802D-S (Dia 8 tube) below and the PEB1202D-S (Dia 12 tube) above. Stepping down to Dia 8 lightens the loop and suits compact actuators; stepping up to Dia 12 lowers restriction on long branch runs feeding multiple consumers. If your port is smaller, the same Dia 10 tube is also available as PEB1001D-S with a 1/8in stud or PEB1003D-S with a 3/8in stud - match the port, not the tube, when choosing the thread. Remember the golden rule of one-touch: the tube OD must equal the fitting size exactly, so a Dia 10 chuck will never hold 3/8in or 12 mm tube.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PEB T-Shaped Straight Thread Tee Connector PEB1002D-S FAQ
It is a Dia 10 mm male branch tee with a 1/4in PT male thread. Working pressure is 0-1.0 MPa (0-10 kgf/cm2), vacuum down to -750 mmHg (10 Torr), proof pressure 1.5 MPa, and operating temperature -20 to +70 C. The -S stainless version carries exactly the same ratings and dimensions as the standard part; only the stud material changes to SUS304.
No. On P-branch families like PEB, AirTAC keeps the push-in body in PBT and makes the male stud SUS304 - the threaded interface with the metal port is the corrosion-critical point. Pressure, temperature, tube and thread ladders and all dimensions are unchanged from the standard PEB1002D, so you can swap one for the other in any existing design.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PEB T-Shaped Straight Thread Tee Connector PEB1002D-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.