Airtac PEB T-Shaped Straight Thread Tee Connector PEB1003
The AirTAC Airtac PEB T-Shaped Straight Thread Tee Connector PEB1003 is a genuine male branch tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale branch tee
- SeriesPEB
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PEB T-Shaped Straight Thread Tee Connector PEB1003
The PEB1003 is an AirTAC PEB male branch tee, a one-touch fitting that turns a single 3/8in PT male port into a branch: one leg screws into the port, the other two legs accept 10 mm OD soft nylon or polyurethane tube. Push the tube home and the internal chuck grips it against the spring gasket; press the POM release ring and the tube slides straight back out.
This is the resin and brass one-touch profile, not the metal BP line: working pressure 0-1.0 MPa, vacuum down to -750 mmHg, proof pressure 1.5 MPa and a temperature window of -20 to +70 C. The body is PBT with a brass stud, and the 3/8in thread arrives with sealant already applied, so it seals on the PT taper without extra tape.
Airtac PEB T-Shaped Straight Thread Tee Connector PEB1003 Technical Specifications
| Model | Airtac PEB T-Shaped Straight Thread Tee Connector PEB1003 |
|---|---|
| Type | Male branch tee |
| Series | PEB |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PEB T-Shaped Straight Thread Tee Connector PEB1003
| PEB | Male branch tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PEB T-Shaped Straight Thread Tee Connector PEB1003 Is Used
Pneumatic manifold branch off an FRL outlet
Screw the 3/8in stud into the FRL or manifold outlet and branch Dia 10 tube to two downstream drops - one to a valve stack, one to a second station - from a single port.
Stopper cylinder feed on a packaging conveyor
Feed Dia 10 tube to a conveyor stopper or gate cylinder while the same port also supplies a proximity sensor blow-off or a small actuator on the branch leg.
Two-actuator supply on a machine frame station
On a robotic pick-and-place cell, use the branch tee at the frame-mounted valve outlet to run parallel Dia 10 lines to a gripper cylinder and a clamping cylinder.
Is the Airtac PEB T-Shaped Straight Thread Tee Connector PEB1003 the Right Part?
On the PEB 3/8in ladder the neighbours are PEB803 below (Dia 8 tube) and PEB1203 above (Dia 12 tube). Dropping to Dia 8 suits lighter cylinder and valve loads with a smaller bore; stepping to Dia 12 cuts pressure drop on longer runs or higher flow branches. Dia 10 with 3/8in is a common mid-ladder choice where the branch feeds a mid-size actuator.
Match the tube OD exactly - a Dia 10 chuck will not hold 10.5 mm or 1/4in tube. If your port is smaller, the same branch shape exists on 1/8in and 1/4in threads (PEB1001, PEB1002); if you need a run tee that keeps the straight-through path, the PED series is that shape instead.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PEB T-Shaped Straight Thread Tee Connector PEB1003 FAQ
It is an AirTAC PEB male branch tee for Dia 10 mm OD soft nylon or polyurethane tube with a 3/8in PT male thread. Working pressure 0-1.0 MPa (0-10 kgf/cm2), negative pressure -750 mmHg (10 Torr), proof pressure 1.5 MPa, operating temperature -20 to +70 C. Body is PBT with a brass stud, POM release ring and chuck, stainless spring gasket and NBR O-ring. Thread comes pre-coated with sealant.
The PEB1003 is designed for exactly that: the 3/8in male stud seats into a port, and the two Dia 10 push-in legs split the flow into two branches. Because it is a branch tee, both tube legs sit at right angles to the stud; if you need the through-path preserved in line with the port, choose the PED run tee instead.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PEB T-Shaped Straight Thread Tee Connector PEB1003
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.